773994

Blendtec Q-Series Manual

10
Zoom out
Zoom in
Previous page
1/16
Next page
10
become blunt, but there is no problem with the mixing power. (The blade is
not sharp.)
• RUNNING SOCKET: The running socket (Refer to Figure 1.2) is subject to
the warranty during the lifecycle of the product.
• The warranty is applied from the delivery date or the purchasing date when
the purchasing certificate is submitted. (The apparent defect or the damage
caused by misuse is not subject to the warranty.)
72. SOLUTIONS FOR POTENTIAL PROBLEMS
WHEN THE MOTOR OF THE BLENDER DOES NOT ROTATE, CHECK THE
FOLLOWING CONTENTS.
• Check whether the main power switch on the lower part of the front is on or
not.
• Check whether the power switch of the fuse box in your house or store is on
or not.
• Pull out the power cord and put it in the outlet again.
• Check whether the LCD screen shows light. (If there is no light, there would
be not enough power for the micro-processor or it would be broken. In such a
case, you must have your product fixed.)
WHEN THE LEVEL OF NOISE FOR THE BLENDER HAS INCREASED
GREATLY IN COMPARISON WITH THE INITIAL LEVEL.
• When the bearing of the jar has been worn out and its lifecycle has been
ended, the level of noise becomes great. (Replace the jar. If you are still in the
warranted period, you can have your defected product replaced.)
• When there is a scratching sound coming from the motor, the lifecycle of the
component of the internal brush has been ended. (You can make an inquiry
at the repairing center of our blender products and have your product or
component replaced.)
• If a loud sound is heard when operating the jar after pulling it out the motor,
you can make an inquiry at the repairing center of our blender products.
WHEN THERE IS SOMETHING WRONG WITH THE MOTOR OF THE
BLENDER, CHECK THE LCD SCREEN. (When there is something wrong with
the motor of the blender, an error message appears on the LCD screen.)
• When ‘OVERTEMP’ appears on the LCD screen: The motor is overheated. In
such a case, the motor can be operated again when the internal temperature
of the motor is decreased to the one for the possible operation. (Pull out
the power cord and cool the motor down for 20 minutes before operating it
again.)
• When ‘OVERLOAD’ appears on the LCD screen: The motor is overloaded.
Keep the switch turned off for 10 seconds. After checking the factors which
disrupt the movement among the blades of the jar, operate it again.
• (If ‘OVERLOAD’ still appears on the LCD screen, or the moving sound is
different from the previous one, have your product repaired.)
• When ‘LOW VOLTAGE’ appears on the LCD screen: There is not enough
power supplied by the motor. Turn off the motor and solve the cause for the
low voltage. (Such a problem usually occurs when the power extension is
used for one power outlet.)
THERE IS A LUMP OR PIECE OF ICE LEFT STILL AFTER THE BLENDING
Downloaded from www.Manualslib.com manuals search engine
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blendtec Q-Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blendtec Q-Series in the language / languages: English as an attachment in your email.

The manual is 1.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info