773992

Blendtec HP3A Home Blender Manual

13
Zoom out
Zoom in
Previous page
1/20
Next page
13
6.4 RESTORING FACTORY DEFAULTS
The Blendtec Home blender has the following blend cycles set as factory defaults for
preset buttons numbered 1, 2, 3, and 4:
Button 1 �����“Slow” cycle
Button 2 �����“Smoothie” cycle
Button 3 �����“Mixed Drinks” cycle
Button 4 �����“Whole Juice” cycle
To restore your blender to these settings, press and hold preset button 4 and
the “START/STOP” button� The display will read, “Restoring Defaults”� When the
programming is complete, the display will read, “Restore Complete” and the blender will
be ready for use�
SECTION 7 - TROUBLESHOOTING
7.1 BLENDER MOTOR WILL NOT TURN ON
If the blender motor will not turn on, try the following:
1� Make sure the main power switch on the back lower-right corner is turned ON�
2� Check your house circuit breaker switch or fuse to make sure it is set to the
ON position�
3� Unplug the power cord from the wall receptacle, wait 5 seconds, then plug power
cord back in�
4� Determine if the Liquid Crystal Display (LCD) is lit� An absence of a lit LCD indicates
a lack of power to the unit�
5� LOOK AT THE LCD:
▶
A reading of “OVERTEMP” indicates that the motor is overheating� The blender has
been disabled until the unit cools to operating temperatures� Turn off and unplug the
unit� Allow it to cool for at least 20 minutes�
▶
A reading of “OVERLOAD” indicates an overload on the motor� Turn off and unplug
the unit� Check the blender jar for blockage and clear if necessary� Remove the
blender jar from the blender motor and check the jar by turning the shaft by hand
to see if it rotates easily� If it does, plug in the unit and turn the blender on again to
clear the overload condition� If overload condition re-occurs, contact your Blendtec
service agent�
▶
BLADE STOPS: If the overload condition stops the blender, remove the blender jar
and carefully check for blockage of the blade� If no blockage is found, replace jar
and use the “PULSE” button on the touch pad to quickly pulse the blade through the
mixture� Once the blade spins freely a programmed button may be used�
▶
A reading of “NO TEMP� SENSOR” indicates the blender computer is not able to
monitor motor temperature� Contact a Blendtec qualified service agent�
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blendtec HP3A Home Blender at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blendtec HP3A Home Blender in the language / languages: English as an attachment in your email.

The manual is 0.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info