Manual Blendtec CONNOISSEUR 825 (page 9 of 19) (English)

626840

Zoom out

Zoom in

1/19

1514

Blend Cycle Pause

When in automatic mode, this setting allows you to pause and resume a blend

cycle at the same time and speed�

To enable or disable the Blend Cycle Pause feature, complete the following steps:

1� Press and hold the cancel/exit button for 3 seconds�

2� Use the scroll button and then select Settings from the menu by touching the

select button�

3� Use the scroll button and then select Blend Cycle Pause from the menu by

touching the select button�

4� Use the select button to toggle between disabling and enabling the blend cycle

pause�

Note: When the Blend Cycle Pause setting is enabled, a cycle can be

paused by pressing any button. If the Blend Cycle Pause function is

disabled, pressing any button disabled will simply stop a blend cycle.

5� Press the cancel/exit button to return to the previous menu�

Slider Lockout (Stealth 875 only)

The Slider Lockout feature allows you to disable the slider bar on the control

surface� When this feature is enabled, only proﬁles on the blender can be used

to operate the blender�

To enable or disable this feature, complete the following steps:

1� Press and hold the cancel/exit button for 3 seconds�

2� Use the scroll button and then select Settings from the menu by touching the

select button�

3� Use the scroll button and then select Slider Lockout from the menu by touching

the select button�

4� Use the select button to toggle between disabling and enabling the slider lockout�

5� Press the cancel/exit button to return to the previous menu�

Language

The menus on the Stealth’s display are available in three languages:

English, French, and Spanish�

To select a language, complete the following steps:

1� Press and hold the cancel/exit button for 3 seconds�

2� Use the scroll button and then select Settings from the menu by touching the

select button�

3� Use the scroll button and then select Language from the menu by touching the

select button�

4� Use the scroll button to ﬁnd your desired language, then press select�

5� Press the cancel/exit button to return to the previous menu�

4.1.11 Blender Statistics

Blend Cycle Counts

You can review the total number of cycles run, the number of cycles run for

each control surface number, the number of times the pulse button has been

used and the number of times the slider control bar has been used (For

Stealth 875 only)�

1� Press and hold the cancel/exit button for 3 seconds�

2� Use the scroll button and then select Cycle Counts from the menu by touching

the select button�

3� Use the scroll button to see the number of cycles run in each category�

4� Press the cancel/exit button to return to the previous menu�

Note: The pulse count refers to pulse sets. For example, touching the pulse

button 5 times in a row will register as 1 pulse count. Touching the pulse

button, then a cycle number and then the pulse button will register as 2

pulse counts.

Diagnostic Error Log

You can review the diagnostic errors that have been logged on the blender�

1� Press and hold the cancel/exit button for 3 seconds�

2� Use the scroll button and then select Diagnostic Counts from the menu by

touching the select button�

3� Use the scroll button to see the how many errors have occurred in each category�

4� Press the cancel/exit button to return to the previous menu�

Exporting Blender Statistics

Exporting blender statistics (cycle counts, errors, settings and ﬁrmware versions)

is a way to save diagnostic information, which Blendtec’s customer service and

repair experts will use if problems arise with your blender�

To export blender statistics to a USB drive, complete the following steps:

1� Use a Phillips screwdriver to remove the USB cover at the top of the right side of

the blender�

2� Plug the USB ﬂash drive into the blender’s USB port�

Note: If the blender is in manual or automatic operation mode, the USB

ﬂash drive menu will automatically load on the screen. If the blender is in

programming mode, go to the main menu and select USB Flash Drive.

3� Use the scroll button to ﬁnd Export Counts, then press the select button� You will

be asked if you want to export counts to the sth-cnts�csv ﬁle�

4� Press the select button again to start the export process�

5� After the export process is ﬁnished, remove the USB drive from the blender and

secure the cover on the USB port with a Phillips screwdriver�

"MULTI *a11569" this message will appear on the display Submitted on 19-7-2022 at 23:01
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blendtec CONNOISSEUR 825 in the language / languages: English as an attachment in your email.

The manual is 3,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blendtec CONNOISSEUR 825

Blendtec CONNOISSEUR 825 User Manual - English, French, Spanish - 156 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blendtec CONNOISSEUR 825 Manual

Product: