Manual Blendtec CHEF 600 (page 15 of 19) (English)

626843

Zoom out

Zoom in

1/19

2726

SECTION 5: CARE AND CLEANING

5.1 CLEANING AFTER USE

1� Add hot water and 1-2 drops of liquid dish soap to the blender jar�

2� Place the lid tightly onto the jar, place the jar on the motor base and press and

hold the pulse button for 5-10 seconds�

3� Rinse all soap from the jar and lid with water�

4� If the jar is stored upside down, shake excess water from the jar after cleaning�

Note: WildSide+™ and FourSide™ jars can be stacked to save space.

5.2 LONG-TERM SANITATION

1� Sanitize the jar per local code by ﬁlling the blender jar with a sanitizer diluted

to the manufacturer’s speciﬁcations� Bleach, properly diluted, can be used�

2� Leave the diluted sanitizer in the jar for 5 minutes�

3� Empty the sanitizer from the jar�

4� Rinse jar thoroughly with water�

5� If the jar is stored upside down, shake excess water from the jar after cleaning�

5.3 MOTOR BASE AND SOUND ENCLOSURE CLEANING

• Ensure the blender is unplugged before cleaning�

• Wipe down the plastic housing of the motor base, gaskets, metal top and

sound enclosure with a clean, damp rag� A mild, all-purpose, nonabrasive

cleaner may be used�

• The drive socket can be cleaned using a cotton swab or toothpick�

• For Stealth blender models, the sound enclosure can also be removed for

cleaning, when necessary�

• Open the sound enclosure lid and use both hands to pull outward on the

lid at the pivot joints� This step will ﬂex the plastic enough for it to spread

and clear its mounting tabs�

• The sound enclosure base can be removed in a similar fashion by pulling

outward at the base of the sound enclosure and ﬂexing the outer walls

enough to clear the mounting tabs�

5.4 CLEANING TIPS AND CAUTIONS

• Do not use stiff bristled brushes or abrasive cloths/pads to clean the blender

base, jar or sound enclosure as this will dull or scratch the surface�

• Do not use a water jet of any kind to clean the motor base�

• NEVER submerge the motor base in water� Doing so will void the warranty�

• Avoid submerging blender jars for more than 5 minutes� Water penetration

through the lower jar seals will reduce the life of the jar�

SECTION 6: TROUBLESHOOTING

While we don’t expect you to have any problems with your blender,

sometimes failures do occur� Use the following guidelines to see if the

problem is easily ﬁxed or requires service�

6.1 BLENDER MOTOR WILL NOT TURN ON (NO POWER)

If the blender motor will not turn on, try the following:

• For the Stealth 875 and Chef 775 look to see if the control surface has an

illuminated power icon, for the Stealth 885, Connoisseur 825, EZ 600 and

Chef 600 determine if the Liquid Crystal Display (LCD) is lit� Absence of those

indicators indicates a lack of power to the unit�

• Check your circuit breaker switch or fuse to make sure it is set to the

ON position�

• Unplug the power cord from the wall receptacle, wait 5 seconds, then plug

power cord back in�

6.2 ERROR MESSAGES ON DISPLAY

STEALTH 875™/STEALTH 885™

Touch Error — This indicates that more than one touch sensor on the blender has

been touched� To avoid this message, touch the center of the desired button�

If this icon remains on when no one is touching the touch area, unplug and re-plug

in the blender� If the problem persists please contact your Blendtec Service Agent�

Overtemp Error — This indicates that the motor is overheating� The blender has

been disabled until the unit cools to operating temperatures� If the blender does

not work after 20 minutes or more of cooling time, please call your Blendtec

Service Agent�

Overload Error — This indicates an overload on the motor�

1� Clear the error message by pressing any button or turning the blender off and

on again�

2� Remove the jar, and run the blender to determine whether the issue relates to

the jar or the motor�

3� With the jar removed, check for blockage in or around the socket on the motor

base and the blade assembly on the jar�

4� Place the jar securely on the motor base, and touch to pulse the blade through

the mixture�

5� Ensure the jar is not loaded with excessively hard or thick ingredients�

If overload condition re-occurs, contact your Blendtec service agent�

Reset Errors — If the following error messages appear, reset the error by

pressing the cancel button or cycle the power by unplugging your blender

and then plugging it back in� If the error does not clear, contact your

Blendtec service agent�

• Error: Overtemp� condition detected

• Error: Overload condition detected

• Error: Temp� sensor not detected

• Error: Zero crossing not detected

• Error: Reset error detected

• Error: Read / Write error detected

• Error: Motor control error detected

• Error: Invalid blend cycle

• Error: Touch controller not detected

• Error: Touch controller output is invalid

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blendtec CHEF 600 in the language / languages: English as an attachment in your email.

The manual is 3,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blendtec CHEF 600

Blendtec CHEF 600 User Manual - English, French, Spanish - 156 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blendtec CHEF 600 Manual

Product: