165767

Blaupunkt vr 2100 velocity Manual

3
Zoom out
Zoom in
Previous page
1/16
Next page
3
Velocity Reference Amplifier VR 250, VR 2100
The amplifier is suitable for connecting to car radios with cinch connector.
Use the Blaupunkt ISO-Cinch Adapter for connecting to car radios with
ISO connector.
Possibilities for use and switching:
VR 250 VR 2100
Max Power 2x100 / 1x300 W Fig. 7 2x200 / 1x600 W
4 Ohm Tri - Mode
Max Power 2x150 / 1x400 W Fig. 7 2x300 / 1x 1000 W
2 Ohm
Max Power 2x230 W Fig. 7 2x400 W
1 Ohm
RMS Power 2x50 / 1x150 W Fig. 7 2x100 / 1x300 W
4 Ohm (THD @ 0.04 %) (THD @ 0.04 %)
RMS Power 2x75 / 1x200 W Fig. 7 2x150 / 1x 500 W
2 Ohm (THD @ 0.06 %) (THD @ 0.05 %)
RMS Power 2x115 W Fig. 7 2x200 W
1 Ohm (THD @ 0.07 %) (THD @ 0.07 %)
Freq. response 10 Hz - 70 kHz 10 Hz - 70 kHz
- 3 dB
Signal-to-Noise > 95 dB > 95 dB
Ratio
Input Level 0,3 - 8 V 0,3 - 8 V
High Pass 40 - 250 Hz 40 - 250 Hz
Low Pass 40 - 120 Hz 40 - 120 Hz
Dimensions 232.6 x 59.5 x 320 232.6 x 59.5 x 380
WxHxD (mm)
Tri-Mode
Allows you to drive two loudspeakers and to connect a third speaker
in mono operation (bridged mode).
Positive/negative connections
We recommend a minimum cross-section of 10 mm
2
. Lay commercially
available positive cable to the battery and connect using fuse holder. The
fuse holder should be connected close to the battery.
Use cable bushings at sharp-edged holes. Screw the commercially
available negative cable firmly to an interference-free earthing-point (car
body bolt, car body sheet, but not to the negative battery pole). Scrape
the contact surface of the earthing point until it is blank metal and coat
with graphite grease.
Connection examples:
Connection of power supply........................................................ Fig. 2
Connection of car radio with cinch socket ................................... Fig. 3
Connection of car radio with loudspeaker output ........................ Fig. 4
Loudspeaker connections ........................................................... Fig. 5
When connecting via the cinch or loudspeaker sockets of the car radio
the switch cable must be connected.
+12V
Controller (GAIN)
Using the Gain Controller you can adjust the input sensitivity of the
Velocity Power Amplifier to the output voltage of your car radio pre-
amplifier output.
The adjusting range is from 0.3 V to 8 V.
When connecting a car radio from other manufacturers the input sensitivity
should be adapted in accordance with the specifications of the
manufacturer.
Introduction (GB)
Congratulations on purchasing this high-quality Car Audio Amplifier. The
development work invested in the new Velocity Amplifier offers you
complete music enjoyment in your car. Our Velocity Amplifiers are fitted
with all typical product features expected from a high-end amplifier, but
also contain a number of technical highlights as well, such as:
• 1 ohm stability (only in stereo mode) for low-ohm amplifier systems
with high performance
• Variable frequency dividers for high and low pass setting
• Variable input voltage 0.3 - 8 V
• Transistors for power supply using MOSPET technology
• Gold-plated screw connectors for loudspeaker and power supply
• Preamp-Out and -In gold-plated
• Bass-Boost
• Chrome-plated amplifier housing
To achieve the best possible sound quality from your new Velocity
Amplifier we recommend that it is installed by an authorised Velocity
dealer and that the matching Velocity Loudspeaker system is used. This
is the way to obtain the full enjoyment of the performance of your
amplifier.
Let us finally mention the aspect of health safety. Please remember when
listening to music in your car that constant sound-pressure levels of more
than 100 dB can cause permanent damage to the human ear right up to
complete loss of hearing. Sound-pressure levels of more than 130 dB
can be achieved with modern high-performance systems and high-
quality loudspeaker configurations.
You can also obtain further information on our Velocity Series at our
Internet address http://www.velocity.de
Safety instructions
Rules to be observed in fitting and connection
Disconnect the negative pole of the car battery for the duration of the
installation and connection works.
The safety instructions of the car manufacturer (airbag, alarm systems,
on-board computers, engine immobilizers) must be observed.
With regard to accident prevention the Velocity power amplifier must be
affixed in a professional manner. The mounting surface must be suitable
for accepting the enclosed screws and must offer secure installation.
When drilling holes please ensure that no car components are damaged
(battery, cables, fuse box).
The amplifier should be installed at a suitable location, i.e. under the
seats or in the boot, Fig. 1.
A dry position should be selected for the installation location that
guarantees sufficient air circulation for the cooling of the amplifier.
Use cable bushings at sharp-edged holes.
Use loudspeakers with 1-2-4 ohm impedance. Pay attention to the max.
loading (music output).
Use 16 mm
2
loudspeaker connection cables. Do not connect the
loudspeakers to earth, use only the designated terminals.
The cross-section of the positive and negative cable may not be less than
10 mm
2
.
Fit a fuse holder to the positive cable between the battery and the
amplifier directly at the battery.
8 622 401 876
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt vr 2100 velocity at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt vr 2100 velocity in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info