614328
3
Zoom out
Zoom in
Previous page
1/12
Next page
- 3 -
Safety information
Installation and connection regulations
You must disconnect the negative terminal of the batte-
ry during the installation and connection of the equip-
ment.
Warning!
You must also comply with all safety instructions pro-
vided by the vehicle manufacturer (alarm system, ve-
hicle immobiliser, airbag)!
Before drilling holes for the mounting brackets or wi-
ring, make sure that you will not damage any existing
wiring or vehicle parts (such as the petrol tank or fuel
lines).
Use cable grommets on sharp-edged holes.
Lay all wiring far enough away from the wiring harness
to prevent interference. The + supply cable must be fit-
ted with a fuse at a maximum of 30 cm from the battery
to protect the vehicle battery and the + supply cable in
the event of a short circuit.
The navigation unit is suitable for vehicles with:
12 volt battery
Negative pole on the chassis
Equipment fuses: 5 A wiring fuse
5 A equipment fuse
Product information
The TravelPilot RGS 06 navigation system is an autonomous
system equipped with an integrated gyro. Following the entry
and activation of a destination, the system provides visual dri-
ving recommendations well in advance of any turn-off points in
the form of pictograms on a 5" colour monitor and spoken dri-
ving information over a separate speaker, thus guiding the
motorist from his/her starting point to a selected destination
via the best available route.
The scope of the functions provided is determined in the spe-
cifications of the CD-ROM used. The CD-ROM for individual
countries + operating manual are available separately.
Notes on the operation of the equipment
To ensure the trouble-free operation of the navigation system,
a distance calibration must be performed after the equipment
has been installed.
The service software integrated into the basic navigation unit
allows you to start up the navigation system and to calibrate
the wheel sensor using the SERVICE MENU following the in-
stallation of the unit or during later servicing. All that is requi-
red is a straight stretch of road of at least 100 m in length. The
software also provides additional service functions for analy-
sing any malfunctions in the navigation system.
The system determines the distance travelled via a connection
to the vehicle’s speedometer signal. If there is no speedome-
ter signal available, it will be necessary to have a wheel sensor
mounted by an authorised customer service agent.
The wheel sensor scans a magnetic strip which is glued to the
wheel rim and delivers information on the distance travelled by
the wheel. Due to automatic length adaptation, the magnetic
strip must be applied to the non-driven left-hand wheel.
The system recognises driving forwards and backwards by
evaluating the back-up signal (forwards = 0 volts, backwards =
12 volts) received via the connection contact (RFLS) provided
for that purpose.
Because of the integrated gyro and CD-ROM drive, it is essen-
tial that the basic navigation unit be installed in a horizontal
position.
Preparing for installation
Before beginning your work, check the equipment to make sure
that everything has been included: ............................ page 7
The following installation steps must be performed:
Installing the navigation unit (computer).......... page 4
Connecting the GPS antenna ............................. page 4
Installing the display ........................................... page 4
Installing the speaker .......................................... page 4
Installing the control unit.................................... page 4
Installing the wheel sensor ................................. page 5
(only for vehicles without a speedometer signal)
Installing the navigation unit
Mounting location for the navigation unit
The navigation unit need not be installed at any particular lo-
cation.
When choosing the mounting location for the navigation unit,
you must make sure that the unit is screwed firmly to the chas-
sis in a horizontal position (you must be able to read the wri-
ting on the flap) while observing the following permissible an-
gles of installation:
Position: right/left min. -5˚ / max. +5˚
sloping towards the rearmin. 0˚ / max. +5˚
A fan has been integrated into the basic navigation unit to pro-
vide cooling in the event that it overheats. The air vents around
the unit must remain uncovered to ensure adequate air circu-
lation. Make sure that there is enough room to insert the navi-
gation CD into the CD drive. Use the enclosed installation ma-
terial in order to mount the navigation unit. See Fig. 1
Positive connection
The navigation unit must be connected to permanent plus 12 V
and positive via the ignition.
Lay the permanent plus 12 V cable (red) to the battery (do not
lay the wiring directly by the cable harnesses). Attach the fuse
holder to protect the positive cable a maximum of 30 cm
from the vehicle battery and connect it to the positive ter-
minal on the battery (if necessary, drill a hole through the
splashboard and use cable grommets accordingly). Connect
the positive switching cable (black) with the fuse holder at ter-
minal 15 (+ switched via ignition) behind the fuse.
In vehicles in which it is not possible to connect the cable in
the fuse box, use the enclosed fuse holder to connect the ca-
ble directly to terminal 15 at the ignition.
Negative connection
Screw the negative cable (brown) directly onto the chassis.
Scratch the contact point for the ground down to the bare me-
tal and grease it with anti-seize graphite petroleum (important
for good grounding).
Connecting the GPS antenna
Safety instructions
Mount the antenna only on a metal roof with magnetic
properties (not suitable for aluminium). Do not mount
the antenna on roofs covered with leather or synthetic
materials.
When mounted on a roof (held only by a magnet), the
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt TravelPilot RGS 06 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt TravelPilot RGS 06 in the language / languages: English as an attachment in your email.

The manual is 4,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blaupunkt TravelPilot RGS 06

Blaupunkt TravelPilot RGS 06 User Manual - English - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info