Manual Blaupunkt tha 475 pnp (page 7 of 52) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish)

166907

Zoom out

Zoom in

1/52

THA 475 PnP

Note:

If the connection is made using a PnP-INPUT cable,

the switch-on is performed automatically.

! As a special feature, +12 V/200 mA are now available

as output switching voltage at the remote input/out-

put after automatic switch-on.

High-level connections (via PnP High-

Inputcable only)

The ampliﬁ er features high-level connections (High

Input) to be able to connect to radio devices without pre-

stage outputs (Fig. 2). This allows for a direct connection

at the loudspeaker output of the radio device.

Note:

Unused Out/Input connectors from the PnP cable must

be connected (see Fig. 2a *).

Direct Aux Input connection

Connection option in case of missing or occupied

AUX input at the car sound system

Various NF sources, such as an MP3 player or

a mobile navigation, can be directly connected

via a 3.5-mm jack plug at the Direct Aux Input.

All signal sources can be listened to at the same

time and their volume is adjusted at the respec-

tive source device.

Note:

All NF sources must be switched off during in-

stallation and connection!

Installing the jack plug cable

Please use our 5-m jack plug cable with order

number 7 607 001 525 for the connection.

One of its special features is an on/off switch.

Switch position OFF (•):

For installation and deinstallation and no con-

nected NF source.

Switch setting ON: (I / II):

Only after an NF source has been connected.

Caution:

For the connection, always adjust the volume

control to minimum and switch off the ampliﬁ er.

If you want to listen to one sound source via

the front and rear loudspeakers, you must con-

nect the Direct Aux inputs with our Y jack plug

cable (7 607 001 524), (see Fig. 6).

Level control

The Level control is used to adjust the input sensitivity

of the power ampliﬁ er to the output voltage of your car

sound system.

The adjustment range is from 0.3 V to 8 V.

A few important explanations in this context:

By turning the control clockwise, the input sensitivity of

the ampliﬁ er and, therefore, also the volume increases.

However, this is not a volume control; no further ampli-

ﬁ er output can be achieved in the end position, even if it

may sound like that at the beginning. The system merely

increases the volume faster if the volume control of the

car sound system is turned up.

Loudspeaker connections

(If the ampliﬁ er is to be jumpered, continue with the sec-

tion "Bridged loudspeaker connections" at this point).

As with every audio component, the correct polarisa-

tion of ampliﬁ er and loudspeakers is of essentially

importance for a good bass response. For this reason,

ensure that the positive (+) connection of the ampliﬁ er

is connected with the positive connection (+) of the

loudspeaker; the same applies to the negative (-) con-

nections. In addition, the left ampliﬁ er channel must

be connected with the left loudspeaker and the right

ampliﬁ er channel with the right loudspeaker.

Bridged loudspeaker connections

Note: Not possible for connection via PnP cable.

The THA 475 PnP ampliﬁ er allows for switching the

channels 1+2 and 3+4 as bridge connection. This allows

the ampliﬁ er to be used for one or several subwoofers

or a mid-range driver. In this conﬁ guration, the ampliﬁ er

combines the right and left channel to a single-channel

output (mono output).

Note:

The ampliﬁ er can add the right and left signal informa-

tion only if the right as well as the left RCA connection

were carried out.

Caution:

In a bridge circuit, the ampliﬁ er load must be 4 ohm

or higher. A lower load leads to an overheating or

switch-off of the ampliﬁ er and can cause permanent

damages.

Adjusting the type and range of the frequency

crossovers

With the THA 475 PnP, the type of frequency crossover

(i.e. "Low Pass" or "Hi-Pass") and the desired crossover

frequency can be adjusted. For example, if a pair of

subwoofers is to be connected, low-pass settings are

required. The crossover frequency is dependent upon

the frequency range of the loudspeakers (see recom-

mended frequency range of the loudspeakers).

High-Pass

At a setting of 250 Hz, the ampliﬁ er has a frequency

range of 250 Hz to 30,000 Hz.

Low-pass frequency control

This control is active if the switch is in the position

"Low-Pass", and allows for setting the desired crossover

frequency.

Example:

At a setting of 150 Hz, the ampliﬁ er has a frequency

range of 10 Hz to 150 Hz.

THA_475_PnP_0507.indd 7THA_475_PnP_0507.indd 7 30.05.2007 12:06:34 Uhr30.05.2007 12:06:34 Uhr

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt tha 475 pnp in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 1,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blaupunkt tha 475 pnp Manual

Product: