613051
27
Zoom out
Zoom in
Previous page
1/33
Next page
24
Stopping the Alarm
Enter a User PIN Code and press OK key on the Control Panel.
Enter a User PIN Code and press Disarm key on the Remote Keypad.
Press Disarm key on the Remote Controller
The alarm will be stopped; the device that triggered the alarm will be displayed on screen. Use
the Down button to scroll down the alarm event, the screen will display whether the system
reported successfully to programmed telephone number or not.
When you finish viewing the alarm event, the system will enter Disarm mode.
Alarm Memory
If an alarm was raised without being silenced during your absence, and the alarm reporting has
been carried out; the screen will continuously show “ALARM! ALARM!” to warn the user.
When you come back and disarm the system, the siren will sound for 3-second to warn you
that the intruder might still be inside your house.
View the alarm event by scrolling down with Down key, when you finish viewing the alarm
event, the system will enter Disarm mode.
Tamper Protection
When the system is under Away mode, if a tamper switch is triggered, an alarm will be
activated immediately. The Control Panel will send a SMS alarm event “Tamper” to
programmed SMS report telephone number, or dial the Voice report telephone number and
play “Burglar” message upon answer.
When the system is under Home or Disarm mode, if a tamper switch is triggered, the Control
Panel will not make any report or activate alarm. The fault LED will light up and a fault event
will be registered in the Control Panel.
Dialling and Call Acknowledgement
When an alarm is activated, the Control Panel will dial the programmed telephone numbers in
priority order for Voice Message or SMS Message report. When the Control Panel makes Voice
Message Reports:
After dialling, the Control Panel will delay 5 seconds then starts to play the message. It will
first play the general part of the recorded message (Address) then plays the specific alarm
message (Burglar, Fire, Medical or Emergency) depending on the nature of the alarm.
To ensure the call is successfully received by the recipient, the recipient should acknowledge
the message by pressing the appropriate button on his telephone set.
If the Control Panel does not receive any acknowledgement, the message will be repeated for
85 seconds. The Control Panel will then consider the call unsuccessful and dial the next
phone number in priority.
NOTE:
1. Remote Controller cannot be used to stop the Emergercy Alarm triggered by itself.
2. If you disarm the system with Remote Controller, the Control Panel screen will continue to
display ALARM!ALARM!message to remind you to check the alarm memory.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt SA 2700 Kit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt SA 2700 Kit in the language / languages: English as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blaupunkt SA 2700 Kit

Blaupunkt SA 2700 Kit User Manual - German - 60 pages

Blaupunkt SA 2700 Kit User Manual - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info