790594
5
Zoom out
Zoom in
Previous page
1/32
Next page
DE
OPTIONEN
Parklinie: bei einigen Modellen verfügbar, siehe Abbildung oben.
Diese Option kann durch Befolgen der Anweisungen für die Schaltschleife
aktiviert werden.
Schalter Spiegel/rechtes Bild: Für einige Modelle verfügbar.
Diese Option kann durch Befolgen der Anweisungen für die Schaltschleife
aktiviert werden.
Schalter Bild oben/unten: Bei einigen Modellen mit Schraubbefestigung erhältlich.
Diese Option kann durch Befolgen der Anweisungen für die Schaltschleife
aktiviert werden.
Anweisungen für die Schaltschleife:
Blaue Schleife: Schneiden, um zur Vorderansicht zu wechseln
Lilafarbene oder weiße Schleife: Schneiden, um die Parklinie zu deaktivieren
Kamerabild ohne Parklinie Kamerabild mit Parklinie
EEqquuaall DDiiaammeetteerr
UUPP
UUPP
B. Installation Guide For Bracket-Mount Camera
Blue loop: Cut to switch to front view
Purple or white loop: Cut to turn off parking line
Switch Loop Instructions:
Wiring Diagram
Remarks:
Beside flush and bracket mount cameras, we also
have bolt mount camera series, which is mounted
by following steps:
1. Select suitable flat position near the license plate light and mark it.
2. Drill a hole according to the bolt diameter.
3. Put the bolt vertically (against ground) into the hole and fix the bolt
with the screw supplied from inside.
4. Some models come with up/down image switch option, and can be
mounted with its bolt horizontal (against ground) and its lens
downward.
1.Choose a flat position near license
plate light and make a small hole
for the first screw with a drill.
2. Use a screw driver to fix the first
screw (but not tightly).
3. Get the power/video cables connected,
and then adjust the camera properly to find
the best position for the other screw
according to the camera image in monitor.
4. Mark the position found for second
screw and make a hole with a drill.
5. Fix the second screw with a
screw driver.
A. Installation Guide For Flush-Mount Camera
B
A
1.Check to be sure the hole saw
used is with equal diameter to
that of camera.
2. Adjust the camera to turn the
UP arrow mark straight upwards.
3. Put the harness through the
hole made on bumper before
fixing the camera.
4. Put the camera into the hole and
use your two thumbs to press it
evenly for tight and flat mounting.
B
A
Special type installation locationUniversal type installation location
Parameters
Current
Consumption
Power
Waterproof Grade
Operating
temperature range
Other
Optional accessories
-20 ~ +65
VK-RVC 4.X (10 meter RCA extension cable); SF-RVC 4.X (signal filter)
Rear view with parking line, formal/ mirror switch, parking line swich, dual-coil control dual
functions
Video signal
Signal
Effective Pixels
Voltage
Min Illumination
CVBS
NTSC
DC12V
0.1 Lux
688X528
<40mA
IP67
Storage
temperature range -30 ~ +80
<0.35W
Kamera
Vebindungsschleife
EEqquuaall DDiiaammeetteerr
UUPP
UUPP
B. Installation Guide For Bracket-Mount Camera
Blue loop: Cut to switch to front view
Purple or white loop: Cut to turn off parking line
Switch Loop Instructions:
Wiring Diagram
Remarks:
Beside flush and bracket mount cameras, we also
have bolt mount camera series, which is mounted
by following steps:
1. Select suitable flat position near the license plate light and mark it.
2. Drill a hole according to the bolt diameter.
3. Put the bolt vertically (against ground) into the hole and fix the bolt
with the screw supplied from inside.
4. Some models come with up/down image switch option, and can be
mounted with its bolt horizontal (against ground) and its lens
downward.
1.Choose a flat position near license
plate light and make a small hole
for the first screw with a drill.
2. Use a screw driver to fix the first
screw (but not tightly).
3. Get the power/video cables connected,
and then adjust the camera properly to find
the best position for the other screw
according to the camera image in monitor.
4. Mark the position found for second
screw and make a hole with a drill.
5. Fix the second screw with a
screw driver.
A. Installation Guide For Flush-Mount Camera
B
A
1.Check to be sure the hole saw
used is with equal diameter to
that of camera.
2. Adjust the camera to turn the
UP arrow mark straight upwards.
3. Put the harness through the
hole made on bumper before
fixing the camera.
4. Put the camera into the hole and
use your two thumbs to press it
evenly for tight and flat mounting.
B
A
Special type installation locationUniversal type installation location
Parameters
Current
Consumption
Power
Waterproof Grade
Operating
temperature range
Other
Optional accessories
-20 ~ +65
VK-RVC 4.X (10 meter RCA extension cable); SF-RVC 4.X (signal filter)
Rear view with parking line, formal/ mirror switch, parking line swich, dual-coil control dual
functions
Video signal
Signal
Effective Pixels
Voltage
Min Illumination
CVBS
NTSC
DC12V
0.1 Lux
688X528
<40mA
IP67
Storage
temperature range -30 ~ +80
<0.35W
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt RVC 4.3 U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt RVC 4.3 U in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 6.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info