716224
18
Zoom out
Zoom in
Previous page
1/24
Next page
TOOL SPECIFIC SAFETY INSTRUCTIONS
When using the tool, always use caution and take on a firm and well-balanced position.
Where possible, avoid working on wet, slippery ground or in any case on uneven or steep ground that does not guarantee
stability for the operator.
Never run, but walk carefully paying attention to the lay of the land and any eventual obstacles.
Assess the potential risks of the area you are cutting and take all necessary precautions to ensure your own safety, especially
on slopes or on bumpy, slippery or unstable ground.
Do not use the tool if you are unable to hold it with both hands or keep it steady on your legs while working.
ASSEMBLY
Warning! To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the product
when assembling parts.
Attaching The Guard
Invert the grass trimmer/edger to access the trimmer head. Using a Phillips head screwdriver, remove the pre-installed screw
from the trimmer head.
Place the guard on to the trimmer head so that the large part of the guard sits to the rear, (Fig.3).
Align the screw hole on the guard with the screw hole on the trimmer head. Insert the screw into the trimmer head, fastening
the guard in place, (Fig.4).
Remove the protective tape from the line cutting blade, (Fig.5).
Adjusting The Front Handle
To avoid injury, adjust the front handle for optimum control and balance.
The front handle can be moved either up and down the shaft, forward and backwards or rotated 360º around the shaft. To find
your optimum desired position unlock the quick release locking lever by pulling outwards, (Fig.6).
Once you have the desired position relock the front handle locking lever by pushing inwards.
Adjusting The Shaft Length
Loosen the lower part of the centre collar (Fig.7). This will allow the lower part of the shaft to be extended or retracted.
When the shaft is at a comfortable length, retighten the collar.
Rotating The Shaft
The shaft can be rotated to the 0 or 180º position for trimming and edging operations.
Pull the upper part of the centre collar (Fig.8). This will allow the motor to be rotated between the 0 or 180º position.
Note: The head will only lock in the 0 or 180º position.
Rotating The Trimmer Head
The trimmer head can be rotated to the 0 or 90º position for trimming and edging operations.
Press the Edger adjustment button, Fig.9, and the trimmer head will spring around 90º. Make sure it is locked into position.
To move the trimmer head back simply press the edger adjustment button again and rotate back to its original position.
Extending The Line
To extend the line press the spool line extension button on the spool, (Fig.10)
Warning! To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the
product when extending the line.
Adjusting The Line Cutting Blade
The cutting line can be set at two lengths (250 & 300mm).
To adjust the line cutting blade turn the line cutting blade adjustment dial by pushing down and rotating 180º (Fig. 11)
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt RTKA 752001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt RTKA 752001 in the language / languages: English, German as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info