162509
2
Zoom out
Zoom in
Previous page
1/20
Next page
- 21 -
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
DANSK
SVENSKA
ESPAÑOL
GB
Safety instructions
Installation and connection regulations
While installing and mounting this equipment, you must
disconnect the negative terminal of the battery. Important: You
must also comply with all safety instructions given by the auto
manufacturer (alarm system, vehicle immobilizer, airbag)!
Before drilling holes for mounting the equipment or laying the
wiring, make sure that no existing wiring or auto parts (such as
the petrol tank, fuel line) will be damaged.
Use wire bushings on sharp-edged holes.
In order to avoid any interference, lay all wiring far enough away
from the wire harnesses.
Equipment fuses:
Basic unit: 5 A wire fuse
5 A miniature fuse
Perfect functioning
In order for the navigation unit to function perfectly, it is necessary to
calibrate the system after the installation. For this purpose, a special
installation and calibration CD-ROM including operating instructions is
required.
Note: At the end of the installation instructions you will find a list of error
messages, a service list and a troubleshooting guide.
Componentry Fig. 1
The navigation componentry consists of a navigation computer with an
integrated CD-ROM drive (navigation unit), a NAVI interface, a GPS
receiver with an antenna, a precision resistor for the rear window
defogger, a magnetic field sensor, wheel sensors, a loudspeaker and
mounting material.
Mounting location for the navigation unit
Remove the transport block (two brass screws in the upper plate)
before beginning the installation work. Keep these screws in a safe
place in case the unit must be set in for servicing. After removing
the screws, insert the enclosed plugs into the holes in the upper
plate.
The navigation unit need not be installed at any particular position.
When choosing the mounting location for the navigation unit, you must
make sure that the unit is installed lying in a horizontal position (you must
be able to read the writing on the flap).
Make sure that there is enough room to insert the navigation CD into the
CD drive. Use the enclosed installation material in order to mount the
navigation unit.Positive connection Fig. 2
Positive connection Fig. 2
The navigation unit must be connected to permanent plus 12 V and
positive via the ignition.
Lay the permanent plus 12 V wire (red) to the battery (do not lay the wiring
directly by the wire harnesses). Attach the fuse carrier to protect the
positive wire and connect it to the positive terminal on the battery (if
necessary, drill a hole through the splashboard and use wire bushings
accordingly).
Connect the switching plus wire (black) with the fuse carrier at terminal
15 (switched to plus via the ignition) behind the fuse. In cars in which it
is not possible to connect the wire in the fuse box, use the enclosed fuse
carrier to connect the wire directly to terminal 15 at the ignition. Remove
the steering wheel panelling first.
Negative connection Fig. 2
Screw the negative wire (brown) directly onto the chassis. Scratch the
contact point for the ground down to the bare metal and grease it with
antiseize graphite petroleum (important for good grounding).
Magnetic field sensor (electronic compass)
Note: You must determine the optimum mounting location for the
magnetic field sensor in each vehicle individually. Before permanently
installing the magnetic field sensor, attach it temporarily and then test
the chosen location with the installation and calibration CD-ROM to
make sure everything operates correctly.
The magnetic field sensor must be installed in the passenger room. It
determines the driving direction by measuring the horizontal earth
magnetic field component. Since the earth magnet field is relatively
small, you must ensure that there is no magnetic or electromagnetic
interference affecting the magnet field sensor at the chosen mounting
location.
Use the enclosed mounts to attach the magnet field sensor to a window
which cannot be opened or, especially where estate wagons or liftback
cars are concerned, mount it without fasteners underneath the inside roof
lining using double-sided sticky tape.
Note: If the magnetic field sensor is mounted in the direct vicinity
of an AM radio antenna integrated into the rear window, it may
cause occasional interference in the radio reception in the long
wave range.
Testing the mounting location of the magnetic field
sensor
Two different tests are required.
1. Test for permanent magnetic interference
Load the installation disk.
Select „find compass location“, and then „compass ellipse“ and drive the
vehicle in a circle. A circle should appear on the display inside the
squares (ideally the circle should be in the centre). If this circle is partially
or entirely outside of the squares, then you must mount the magnetic field
sensor in a different place.
2. Testing for interference caused by other electrical equipment
Load the installation disk, select „find compass location“ and then
„compass error“.
Press „reset“, switch on the consumers (e.g. sliding sun roof, rear window
wiper).
The value indicated for „Loc. error“ must be less than 3.5.
Press reset each time you switch on a different piece of electrical
equipment.
After having tested each piece of electrical consumer individually, check
logical combinations as well. The sum of the values for the consumers
must not exceed a „Loc. error“ of 3.5.
If the value registered exceeds 3.5, then you must mount the magnetic
field sensor in a different location.
Note: Do not switch on the rear window defogger while testing for
interference from the electrical equipment. Any interference caused
by the rear window defogger is registered separately during
calibration and then compensated.
Precision resistor for the rear window defogger
(shunt)
The precision resistor has 2 connection wires and 1 measuring wire:
1. Connection to the ground contact of the rear window defogger
(length: 250 cm),
2. Connection to the vehicle chassis (length: 75 cm),
3. Measuring wire to the navigation unit (length: 50 cm), Fig. 3
The mounting location of the precision resistor depends on the length of
the wiring.
Do not lengthen the connection wires for the ground contact and the
vehicle chassis. Do not attach the connection for the vehicle chassis to
the liftback in estate wagons or liftback cars. Select the mounting location
for the precision resistor so that any heat build-up will be eliminated
(chassis metal).
Lay the measuring wire to the navigation unit and connect it to the
corresponding jack of the compact plug, Fig. 3
Note: No other electrical equipment (e.g. rear window wiper) may be
connected to the ground contact for the rear window defogger, except for
the rear window defogger.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt rgs 05 travel pilot at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt rgs 05 travel pilot in the language / languages: English as an attachment in your email.

The manual is 7,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blaupunkt rgs 05 travel pilot

Blaupunkt rgs 05 travel pilot User Manual - English - 36 pages

Blaupunkt rgs 05 travel pilot Installation Guide - German - 20 pages

Blaupunkt rgs 05 travel pilot User Manual - German - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info