Manual Blaupunkt new york rdm 127 (page 8 of 21) (English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish)

165726

Zoom out

Zoom in

1/21

- 8 -

Connection

1 In order to obtain full car radio output power and to avoid any

electrical wrong connections with ISO plugs installed in the car, the

car’s ISO plug must not be directly connected to the car radio.

2 You can avoid making incorrect connections by using the vehicle-

specific Blaupunkt adapter wiring, but !

3 Due to the limited cross-section of the wiring in the vehicle, it is

necessary to use the connection cable 7 607 884 093 in addition to

the vehicle-specific Blaupunkt adapter wiring for the positive/

negative connection.

Be sure to observe Fig. 4, 5

When using the vehicle-specific adapter cable, cut off the radio’s

connector and employ the connecting cable

7 607 884 093.

Advantage: The vehicle’s wiring system is not damaged.

Positive connection

Connect the permanent +12 V lead (incl. anti-interference choke coil)

with the connecting cable 7 607 884 093 and attach directly to the

positive pole of the battery. Connect the illumination and antenna

leads and the ACC ignition lead (+12 V / terminal 15) to the

connecting cable as well.

Negative connection

Do not connect the negative lead to the negative pole of the battery!

Connect the negative cable with the connecting cable 7 607 884 093.

Lay the negative line to a suitable ground, such as a chassis screw or

the chassis itself. Cut the ground line as necessary

(do not form line loops).

The car radio is designed to be installed in the car radio compartment

provided by the vehicle manufacturer. Open the car radio compartment

(remove the shelf or panel by unclipping it) or adjust the size of the car

radio compartment to measure 182 x 53 mm.

For vehicles with deviating installation compartments, Blaupunkt offers

installation kits for 50 mm radio units for the most popular vehicle models.

Check the installation situation in the vehicle and, if necessary, use one

of the special installation kits for specific vehicle models,

e.g. Audi A4/A6/A8: 7 608 021 473

Note:

The mounting bracket included with this car radio is designed for

installation in vehicles with a standard DIN installation compartment

measuring 182 x 53 mm, 165 installation depth and an instrument panel

thickness of approximately 1 to 20 mm in the area of the tab fasteners,

see Fig. 1.

Reach behind the car radio compartment and check to see which tab

fasteners can be bent for the mounting bracket.

Note: Try to be sure to bend all of the tabs.

Place the mounting bracket in the compartment and bend over the tabs

with the help of a screwdriver, see Fig. 1, 2.

Connection, see page 4 or 5 or 6

Connection instructions............................................................... Fig. 4

Positive/negative connection with vehicle-specific

adapter cable .............................................................................. Fig. 5

Positive/negative connection with connection line

7 607 884 093 ........................................................................... Fig. 5a

Equalizer or amplifier connection, (CINCH) ................................ Fig. 6

Do not connect the control wire to terminal 15 (+12 V switched) or

terminal 30 (permanent +12 V), maximum load < 150 mA.

Connection of 4 loudspeakers (4/35 W)...................................... Fig. 7

LF = left front, RF = right front, LR = left rear, RR = right rear.

CD player connection CDC-F07 ................................................. Fig. 8

Connection of IR remote control RC-07 ...................................... Fig. 9

Use the connection cable attached to the remote control.

If necessary, also use cables 7 607 647 093 and 7 607 648 000.

Connection SUB-OUT(CINCH) ................................................. Fig. 10

Connection AUX L/R (CINCH) = 1 V......................................... Fig. 11

Test microphone) ...................................................................... Fig. 12

The test microphone is used for the measurements of unwanted noise,

for the DNC cpntrol and for the HiFi and DNC calibration.

Connection in vehicles with QuickOut

In vehicles equipped with a QuickOut (currently Opel), the QuickOut unit

must be removed and the adapter cable used.

Installing the car radio

Place the car radio in the front of the mounting bracket and push it in until

the side springs snap into position on the left and the right (you will hear

an audible click).

Removing the car radio

Insert the handles into the holes in the panel on the left and right of the

radio and push them in until you hear a distinct click (unlocks side

springs).

Pull the unit out using both handles, see Fig. 3

Note: Handles which have snapped into place can only be

removed after you have pulled the radio out of the

compartment.

DNC (masking of driving noises)

For a description of the equaliser setting and the DNC calibration

process (masking of driving noises) please refer to the owner's manual.

This information is subject to change without notice!

Car radio connection

ISO plug in the vehicle

Car radio connection

with adapter wiring

Car radio connection

with adapter and connection wiring

8 622 400 780

8 601 910 002

Fig. 2

Fig. 3

Fig. 1

Illustrations

182

165

8 601 310 742

1-20

+12V/Kl15

+12V

per.+12V

+12V/Kl15

+12V

per.+12V

+12V

per.+12V

+12V

15A

7 607 884 093

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt new york rdm 127 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 1,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blaupunkt new york rdm 127 Manual

Product: