614924
3
Zoom out
Zoom in
Previous page
1/14
Next page
3
GB
Introduction
Congratulations on your purchase of a high-quality MPA power
amplifier. By selecting the MPA-160 you have chosen a product
which delivers superlative reproduction quality. Whether you are
upgrading an existing system or using the MPA power amplifier in
a new system, you are certain to notice immediate performance
benefits!
Recommendation:
A power amplifier’s performance is only as good as its installation. Proper
installation will maximise the overall performance of your audio system.
We recommend that you have our product installed professionally. Should
you decide to install the amplifier yourself, however, please read through
these instructions carefully, and take your time over the installation.
Finally, a word about your health: please bear in mind when playing
music in your car that sustained sound levels above 100 dB can damage
your hearing and may even result in total hearing loss. Modern high-
performance systems and high-quality loudspeaker configurations are
quite capable of generating noise levels above 130 dB
Safety precautions
Instructions for installation and connection
Fit a fuse in the amplifier power line no more than 30 cm from the vehicle
battery, in order to protect the battery in the event of a short-circuit
between it and the power amplifier. The amplifiers own fuse protects
the amplifier itself, but not the car battery. Disconnect the negative
terminal of the battery before carrying out installation and
connection work.
Observe the vehicle manufacturer’s safety instructions (regarding air-
bags, alarm systems, trip computers, vehicle immobilisers).
The final stage must be installed professionally for reasons of safety.
The mounting surface must be suitable for the screws provided, and
must provide firm support.
When drilling holes, take care to avoid damage to vehicle components
(battery, cables, fuse boxes).
Fit the amplifier in a suitable location, e.g. beneath the seats or in the
trunk (Fig. 1). The mounting location must also be dry, and provide suf-
ficient ventilation for cooling of the amplifier. Use cable grommets when
passing cables through holes with sharp edges. Use loudspeakers with
an impedance of 2 to 4 (see table or installation drawing). Observe
the max. power handling specifications (music output). Do not connect
the loudspeakers to ground; only use the terminals provided. The cross-
section of the positive and negative cable must be at least 6 mm
2
.
MPA 160 amplifier
The amplifier is suitable for connection to car radios with Cinch connec-
tor. Use the Blaupunkt ISO Cinch adapter to connect the amplifier to car
radios with ISO connector. (7 607 893 093/ 7 607 855 094)
Applications and loudspeaker connection:
MPA 160
Stereo mode 2 x 80 Watts / 4 Fig. 7
Max power 2 x 135 Watts / 2
Mono mode Fig. 8
Max power 1 x 160 Watts / 4
Stereo mode 2 x 30 Watts / 4 Fig. 7
RMS Power 2 x 50 Watts / 2
Mono mode Fig. 8
RMS Power 1 x 90 Watts / 4
Tri mode 4 Fig. 9
Frequency
response 20 Hz-50 kHz
Signal-to-noise > 90 dB
ratio
Input sensitivity 0.3 - 4 V
Low-pass filter 75 Hz/100 Hz
(12 dB/Oct.)
Dimensions
WxHxD (mm) 220 x 57 x 170
Positive/negative connection
We recommend a cable cross-section of not less than 6 mm
2
. Run a
standard commercial positive cable to the battery and connect to the
fuse holder. Use cable grommets when passing cables through holes
with sharp edges. Bolt a standard commercial negative cable to a ground
point free of induced noise (car body bolt, body panel) - not to the nega-
tive battery pole. Clean the contact surface of the ground point down to
bare metal and coat with antiseize graphite petroleum.
Integral fuses
The integral fuses within the amplifier protect the final stage and the
entire electrical system in the event of a fault. Never bridge fuses or
replace fuses with a higher current rating.
Example connections
Power supply connection ............................................................ Fig. 2
Connection to car radios with ISO terminal using the
Cinch jack ................................................................................... Fig. 3
Connection to car radios with Cinch output ................................ Fig. 4
Connection to car radios with loudspeaker output ...................... Fig. 5
Car radios with 20-pole connector systemuse adapter
cable 7 607 893 093 ................................................................... Fig. 6
Loudspeaker connections ...................................................... Fig. 9-12
Connect remote amplifier connection to switchable
+12 V power source.
This enables the amplifier to be switched on and off with the radio’s On/
Off switch.
High-level inputs
The amplifier is equipped with high-level inputs to permit connection to
radios without preamp outputs (Fig. 5). This enables direct connection
to be made to the radio’s loudspeaker output.
Gain control
The gain control enables the input sensitivity of the final stage to be
matched to the output voltage of your car radio preamp output.
The range of adjustment extends from 0.3 V to 4 V. The control is preset
to 2 V for Blaupunkt car radios.
Adjust the input sensitivity in accordance with the manufacturer’s speci-
fications when connecting the amplifier to other radios.
Important: Turning the gain control clockwise increases the input sen-
sitivity of the amplifier, and thereby also the volume. The gain control is
however
not a volume control; an increase in volume is not achieved in
the maximum position, even if this subjectively appears to be the case.
The system merely increases the volume more quickly when the volu-
me is turned up on the radio.
Tri-mode loudspeaker connections
MPA amplifiers can be used in a combined mono/stereo mode (Fig. 9).
This facility enables the amplifier to be used simultaneously with stereo
satellite speakers (mid-range and tweeter) and a mono subwoofer.
The connections are somewhat more complicated in this case, as they
require the use of passive crossover networks (not supplied with the
amplifier) which divide the frequency ranges between the various
loudspeakers. The requisite connections can be taken from the diagrams
below.
If you do not wish to purchase and connect the components separately,
a number of ready-assembled tri-mode crossover networks are availa-
ble. Ask your local car audio retail store for details.
CAUTION: In tri-mode (combined mono/stereo mode) the amplifier must
be presented with a load of at least 2 Ohms (stereo satellite speakers)
or 4 Ohms (mono subwoofers). Lower loads cause overheating of the
amplifier and may damage it permanently.
Loudspeaker connections
(If the amplifier is to be connected in a bridged mode, proceed with the
section “Bridged loudspeaker connections”.)
As with any audio component, connection of the amplifier and speakers
with the correct polarity is essential for good bass reproduction. Ensure
therefore when connecting that the positive (+) amplifier terminal is con-
nected to the positive (+) loudspeaker terminal. The same applies to the
negative (-) terminals. The left-hand amplifier channel must also be con-
nected to the left-hand loudspeaker and the right-hand amplifier chan-
nel to the right-hand loudspeaker.
Bridged loudspeaker connections
The MPA can also be bridged in a mono configuration. This enables you
to use the amplifier for one or more subwoofer(s) or a mid-range spea-
ker. In this configuration the amplifier sums the right-hand and left-hand
channels, delivering a single channel (mono) output.
Note: The amplifier can sum the right- and left-hand signal information
only if both the right- and left-hand RCA connections have been made.
CAUTION: The amplifier must be presented with a load of 4 Ohms
or higher in bridged mode. A lower load will cause the amplifier to
overheat or switch off. This can lead to permanent damage of the
unit.
+12V
8 622 401 299
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt MPA 160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt MPA 160 in the language / languages: All languages as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info