Manual Blaupunkt GTA 41200 HP (page 6 of 36) (English, German, French, Italian, Polish, Portuguese, Spanish)

614185

Zoom out

Zoom in

1/36

GTA 41200 HP

Integrate fuse (2 x 25 A)

The fuse integrated in the ampli er protects the output stage

and the entire electrical system in case of a malfunction. If a

replacement fuse is used, never bridge fuses or replace them

with a type with higher current.

Connection examples

Connection of the voltage supply ..................................Fig. 2

Audio inputs ...........................................................................Fig. 3

Loudspeaker connections .................................................Fig. 4 - 7

Remote connection of the ampli er with switchable +12 V

voltage source.

This allows the ampli er to be switched on and o using the

on/o -switch of the car sound system.

Loudspeaker connections

(If the ampli er is to be jumpered, continue with the section

"Bridged loudspeaker connections" at this point).

As with every audio component, the correct polarisation of

ampli er and loudspeakers is of essentially importance for a

good bass response. For this reason, ensure that the positive

connection (+) of the ampli er is connected with the posi-

tive connection (+) of the loudspeaker; the same applies to

the negative connections (-). In addition, the left ampli er

channel must be connected with the left loudspeaker and

the right ampli er channel with the right loudspeaker.

Bridged loudspeaker connections

The GTA ampli er can also be bridged for a mono con gura-

tion. This allows the ampli er to be used for one or several

subwoofers or a mid-range driver. In this con guration, the

ampli er combines the right and left channel to a single-

channel output (mono output).

Note:

The ampli er can add the right and left signal information

only if the right as well as the left cinch (RCA) connection

were carried out.

Caution:

In a bridge circuit, the ampli er load must be 4 Ω or

higher. A lower load leads to an overheating or switch-

o of the ampli er and can cause permanent damages.

Subwoofer connection

The GTA 41200 HP features di erent options of connecting

a subwoofer:

–An active subwoofer or an additional ampli er are

connected with a cinch (RCA) cable to the two LINE OUT

sockets (see Fig.7).

–A passive subwoofer is connected to the bridged loud-

speaker output (see the section "Bridged loudspeaker

connections").

Sound settings

The following options are available to optimise the sound

of the connected loudspeakers:

– BASS switch

The BASS switch is used to adjust the bass response of

the ampli er. The following settings are possible: 0 dB /

+6 dB / +12 dB.

– X-OVER switch and LOW PASS control

For the GTA 41200 HP, the type of frequency crossover

("Low-Pass" or "High-Pass") and the desired cut-o fre-

quency can be adjusted for the connected loudspeakers.

Select the cut-o frequency up to which lower frequencies

(high-pass) or higher frequencies (low-pass) should be

blocked. Only frequencies above the cut-o frequency

(high-pass) or below the cut-o frequency (low-pass) are

passed on to the loudspeakers.

The cut-o frequency is dependent upon the frequency

range of the loudspeakers (see recommended frequency

range of the loudspeakers).

"High-Pass" (switch setting: HI PASS)

With a setting of 80 Hz, the ampli er has a frequency range

from 80 Hz to 30,000 Hz.

"Low-Pass" (switch setting: LOW PASS)

This control is active if the switch is in the LOW PASS posi-

tion, and allows for setting the desired entry frequency.

Example:

At a setting of 150 Hz, the ampli er has a frequency range

of 10 Hz to 150 Hz.

"Full Range" (switch setting: FLAT)

In this switch setting, the frequency control is deactivated

and the entire frequency spectrum is being ampli ed.

– LEVEL control

The LEVEL control is used to adjust the input sensitivity

of the power ampli er to the output voltage of your car

sound system preampli er output. The adjustment range

is from 0.2 V to 5 V. If a car sound system of a third party

manufacturer is connected, the input sensitivity must be

adjusted corresponding to the manufacturer data.

A few important explanations in this context:

By turning the LEVEL control clockwise, the input sen-

sitivity of the ampli er and, therefore, also the volume

increases. However, this is not a volume control. In the

end position, it is not possible to achieve a higher ampli-

 er output, even if it sounds like that at  rst. The system

merely increases the volume faster if the volume control

of the car sound system is turned up.

Power-on indicator (POWER / PROTECT)

Green LED:

Output stage on, regular operating status.

Red LED:

Output stage is electronically switched o due to an error.

GTA_41200_HP_13LG.indd 6GTA_41200_HP_13LG.indd 6 20.08.13 09:4920.08.13 09:49

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt GTA 41200 HP in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blaupunkt GTA 41200 HP Manual

Product: