Manual Blaupunkt gta 280 new (page 3 of 12) (English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish, Spanish)

167414

Zoom out

Zoom in

1/12

8 622 403 270

Safety precautions

Instructions for installation and connection

Fit a fuse in the amplifier power line no more than 30 cm from the vehi-

cle battery, in order to protect the battery in the event of a short-circuit

between it and the power amplifier. The amplifier’s own fuse protects

the amplifier itself, but not the car battery. Disconnect the negative

terminal of the battery before carrying out installation and connec-

tion work.

Observe the vehicle manufacturer’s safety instructions (regarding air-

bags, alarm systems, trip computers, vehicle immobilisers).

The final stage must be installed professionally for reasons of safety.

The mounting surface must be suitable for the screws provided, and

must provide firm support.

When drilling holes, take care to avoid damage to vehicle components

(battery, cables, fuse boxes).

Fit the amplifier in a suitable location, e.g. beneath the seats or in the

trunk (Fig. 1). The mounting location must also be dry, and provide suf-

ficient ventilation for cooling of the amplifier. Use cable grommets when

passing cables through holes with sharp edges. Use loudspeakers with

an impedance of 2 to 4 Ω (see table or installation drawing). Observe

the max. power handling specifications (music output). Do not connect

the loudspeakers to ground; only use the terminals provided. The cross-

section of the positive and negative cable must be at least 6 mm

GTA 280 amplifier

The amplifier is suitable for connection to car radios with Cinch connec-

tor. Use the Blaupunkt ISO Cinch adapter to connect the amplifier

to car radios with ISO connector. (7 607 893 093/ 7 607 855 094)

Applications and loudspeaker connection

Stereo-Mode

Max Power 2 x 80 Watt / 4 Ω Fig.3

Mono-Mode

Max Power 1 x 220 Watt /4 Ω Fig.4

Stereo-Mode

RMS Power 2 x 40 Watt / 4 Ω Fig.3

Mono-Mode

RMS Power 1 x 110 Watt / 4 Ω Fig.4

Frequency response 10 Hz - 26.000 Hz

Signal-to-noise ratio > 80 dB

Stability 2 Ω

Input- 0,3 - 8 V

sensitivity

Low-pass filter 40 - 460 Hz

High-Pass filter 65 - 4500 Hz

Dimensions

D x W x H (mm) 170 x 57 x 243

Positive/negative connection

We recommend a cable cross-section of not less than 6 mm

. Run a

standard commercial positive cable to the battery and connect to the

fuse holder. Use cable grommets when passing cables through holes

with sharp edges. Bolt a standard commercial negative cable to a ground

point free of induced noise (car body bolt, body panel) - not to the neg-

ative battery pole. Clean the contact surface of the ground point down

to bare metal and coat with antiseize graphite petroleum.

Integral fuses

The integral fuses within the amplifier protect the final stage and the

entire electrical system in the event of a fault. Never bridge fuses or

replace fuses with a higher current rating.

Example connections

Power supply connection ............................................................ Fig. 2

Connection of car radio with cinch output ................................... Fig. 3

Loudspeaker connections ........................................................ Fig. 3-5

+12V

Connect remote amplifier connection to switchable

+12 V power source.

This enables the amplifier to be switched on and off with the radio’s On/

Off switch.

Level control

The Level control enables the input sensitivity of the final stage to be

matched to the output voltage of your car radio preamp output.

The range of adjustment extends from 0.3 V to 8 V.

Adjust the input sensitivity in accordance with the manufacturer’s spec-

ifications when connecting the amplifier to other radios.

Important: Turning the Level control clockwise increases the input sen-

sitivity of the amplifier, and thereby also the volume. The Level control is

however not a volume control; an increase in volume is not achieved in

the maximum position, even if this subjectively appears to be the case.

The system merely increases the volume more quickly when the vol-

ume is turned up on the radio.

Loudspeaker connections

(If the amplifier is to be connected in a bridged mode, proceed with the

section “Bridged loudspeaker connections”.)

As with any audio component, connection of the amplifier and speakers

with the correct polarity is essential for good bass reproduction. Ensure

therefore when connecting that the positive (+) amplifier terminal is con-

nected to the positive (+) loudspeaker terminal. The same applies to the

negative (-) terminals. The left-hand amplifier channel must also be con-

nected to the left-hand loudspeaker and the right-hand amplifier chan-

nel to the right-hand loudspeaker.

Bridged loudspeaker connections

The GTA can also be bridged in a mono configuration. This enables you

to use the amplifier for one or more subwoofer(s) or a mid-range speak-

er. In this configuration the amplifier sums the right-hand and left-hand

channels, delivering a single channel (mono) output.

Note: The amplifier can sum the right- and left-hand signal information

only if both the right- and left-hand RCA connections have been made.

CAUTION: The amplifier must be presented with a load of 4 Ohms

or higher in bridged mode. A lower load will cause the amplifier to

overheat or switch off. This can lead to permanent damage of the

unit.

GTA 280

The type of crossover (i.e. “low-pass” or “hi-pass”) and the desired cros-

sover frequency can be selected on the GTA 280. If, for example, you

wish to drive a pair of subwoofers, connect in accordance with the low-

pass diagram (fig. 2a).The crossover frequency is dependent upon the

loudspeaker frequency range (consult the loudspeaker manufacturer’s

data for the recommended frequency range).

“High- Pass” frequency control

This control is active when the switch is in the “Hi-pass” position, and

permits selection of the desired crossover frequency. Example: at a of

65 Hz, the loudspeaker has a frequency range of 65 Hz to

26.000 Hz.

“Low-pass” frequency control

This control is active when the switch is set to “Low-pass” and permits

selection of the desired crossover frequency. Example: at a setting of

40 Hz, the loudspeaker has a frequency range of 40 Hz to 10 Hz.

Operating indicator (POWER / PROTECTION)

Green lamp: Power amp on, regular operating condition

Red lamp: Power amp has been switched off electronically, due to a fault

or failure.

This information is subject to change without notice!

Introduction

Félicitations! Vous avez acheté un amplificateur GTA haut de gam-

me. En optant pour un GTA 280 vous avez choisi une reproduction

du son de très haute qualité. Que vous intégriez l‘amplificateur

GTA dans un système déjà existant ou dans un nouveau système

hi-fi, l‘amélioration de la qualité du son, que vous aurez bien du

mal à ne pas remarquer, vous convaincra dès le premier instant

d‘écoute!

Blaupunkt s’efforce en permanence de rendre les instructions de ser-

vice de ses appareils toujours plus claires et de lecture facile. Si malgré

cela, vous émettiez des doutes sur un point quelconque du manuel,

n’hésitez pas à vous adresser à votre représentant agréé Blaupunkt ou

à composer le numéro du centre d’assistance téléphonique de votre

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt gta 280 new in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish, Spanish as an attachment in your email.

The manual is 0,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blaupunkt gta 280 new Manual

Product: