Manual Blaupunkt gta 200 (page 3 of 12) (English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish)

167410

Zoom out

Zoom in

1/12

Introduction

Congratulations on your purchase of a high-quality GTA power

amplifier. By selecting the GTA 200 you have chosen a product

which delivers superlative reproduction quality. Whether you are

upgrading an existing system or using the GTA power amplifier in

a new system, you are certain to notice immediate performance

benefits!

Recommendation:

A power amplifier’s performance is only as good as its installation. Proper

installation will maximise the overall performance of your audio system.

We recommend that you have our product installed professionally. Should

you decide to install the amplifier yourself, however, please read through

these instructions carefully, and take your time over the installation.

Finally, a word about your health: please bear in mind when playing

music in your car that sustained sound levels above 100 dB can dam-

age your hearing and may even result in total hearing loss. Modern

high-performance systems and high-quality loudspeaker configurations

are quite capable of generating noise levels above 130 dB

Safety precautions

Instructions for installation and connection

Fit a fuse in the amplifier power line no more than 30 cm from the vehi-

cle battery, in order to protect the battery in the event of a short-circuit

between it and the power amplifier. The amplifier’s own fuse protects

the amplifier itself, but not the car battery. Disconnect the negative

terminal of the battery before carrying out installation and connec-

tion work.

Observe the vehicle manufacturer’s safety instructions (regarding air-

bags, alarm systems, trip computers, vehicle immobilisers).

The final stage must be installed professionally for reasons of safety.

The mounting surface must be suitable for the screws provided, and

must provide firm support.

When drilling holes, take care to avoid damage to vehicle components

(battery, cables, fuse boxes).

Fit the amplifier in a suitable location, e.g. beneath the seats or in the

trunk (Fig. 1). The mounting location must also be dry, and provide suf-

ficient ventilation for cooling of the amplifier. Use cable grommets when

passing cables through holes with sharp edges. Use loudspeakers with

an impedance of 2 to 4 Ω (see table or installation drawing). Observe

the max. power handling specifications (music output). Do not connect

the loudspeakers to ground; only use the terminals provided. The cross-

section of the positive and negative cable must be at least 6 mm

GTA 200 amplifier

The amplifier is suitable for connection to car radios with Cinch connec-

tor. Use the Blaupunkt ISO Cinch adapter to connect the amplifier

to car radios with ISO connector. (7 607 893 093/ 7 607 855 094)

Applications and loudspeaker connection:

Positive/negative connection

We recommend a cable cross-section of not less than 6 mm

. Run a

standard commercial positive cable to the battery and connect to the

fuse holder. Use cable grommets when passing cables through holes

with sharp edges. Bolt a standard commercial negative cable to a ground

point free of induced noise (car body bolt, body panel) - not to the neg-

ative battery pole. Clean the contact surface of the ground point down

to bare metal and coat with antiseize graphite petroleum.

Integral fuses

The integral fuses within the amplifier protect the final stage and the

entire electrical system in the event of a fault. Never bridge fuses or

replace fuses with a higher current rating.

Example connections

Power supply connection ............................................................ Fig. 2

Loudspeaker connections ........................................................ Fig. 3-5

Connect remote amplifier connection to switchable

+12 V power source.

This enables the amplifier to be switched on and off with the radio’s On/

Off switch.

Gain control

The gain control enables the input sensitivity of the final stage to be

matched to the output voltage of your car radio preamp output.

The range of adjustment extends from 0.1 V to 8 V.

Adjust the input sensitivity in accordance with the manufacturer’s spec-

ifications when connecting the amplifier to other radios.

Important: Turning the gain control clockwise increases the input sen-

sitivity of the amplifier, and thereby also the volume. The gain control is

however not a volume control; an increase in volume is not achieved in

the maximum position, even if this subjectively appears to be the case.

The system merely increases the volume more quickly when the vol-

ume is turned up on the radio.

Tri-mode loudspeaker connections

GTA amplifiers can be used in a combined mono/stereo mode (Fig. 5).

This facility enables the amplifier to be used simultaneously with stereo

satellite speakers (mid-range and tweeter) and a mono subwoofer.

The connections are somewhat more complicated in this case, as they

require the use of passive crossover networks (not supplied with the

amplifier) which divide the frequency ranges between the various loud-

speakers. The requisite connections can be taken from the diagrams

below.

If you do not wish to purchase and connect the components separately,

a number of ready-assembled tri-mode crossover networks are availa-

ble. Ask your local car audio retail store for details.

CAUTION: In tri-mode (combined mono/stereo mode) the amplifier must

be presented with a load of at least 2 Ohms (stereo satellite speakers)

or 4 Ohms (mono subwoofers). Lower loads cause overheating of the

amplifier and may damage it permanently.

Loudspeaker connections

(If the amplifier is to be connected in a bridged mode, proceed with the

section “Bridged loudspeaker connections”.)

As with any audio component, connection of the amplifier and speakers

with the correct polarity is essential for good bass reproduction. Ensure

therefore when connecting that the positive (+) amplifier terminal is con-

nected to the positive (+) loudspeaker terminal. The same applies to the

negative (-) terminals. The left-hand amplifier channel must also be con-

nected to the left-hand loudspeaker and the right-hand amplifier chan-

nel to the right-hand loudspeaker.

Bridged loudspeaker connections

The GTA can also be bridged in a mono configuration. This enables you

to use the amplifier for one or more subwoofer(s) or a mid-range speak-

er. In this configuration the amplifier sums the right-hand and left-hand

channels, delivering a single channel (mono) output.

Note: The amplifier can sum the right- and left-hand signal information

only if both the right- and left-hand RCA connections have been made.

CAUTION: The amplifier must be presented with a load of 4 Ohms

or higher in bridged mode. A lower load will cause the amplifier to

overheat or switch off. This can lead to permanent damage of the

unit.

Note: If the amplifier is to be used in the tri-mode configuration, the

crossover frequency selector switch must be set to „Flat“ in order to

make the full frequency range available.

Adjustment of the type and range of the cross-over frequencies.

GTA 200

The GTA 200 has a special subwoofer crossover frequency which can

be selected between 40Hz and 160 Hz. The crossover can be bridged

by turning the selector switch to the “Flat” position.

This information is subject to change without notice!

+12V

8 622 402 413

Stereo mode

Max power 2 x 100 Watt / 4 Ω Fig.3 / 3a

Mono mode

Max power 1 x 400 Watt /4 Ω Fig.4

Stereo mode

RMS Power 2 x 50 Watt / 4 Ω Fig.3 / 3a

Mono mode

RMS Power 1 x 160 Watt / 4 Ω Fig.4

Tri mode Fig.5

Frequency response 10 Hz - 55.000 Hz

Signal-to-noise ratio > 80 dB

Stabilility 2Ω

Input 0,1 - 8 V

sensitivity

Low-pass filter 40 - 160 Hz

High-pass filter 100 Hz

Bass-Boost 0 / 9 / 18 dB

Preamp - In / -Out gold-plated

Dimensions

D x W x H (mm) 218 x 60 x 245,6

GTA 200

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt gta 200 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blaupunkt gta 200 Manual

Product: