614186

Blaupunkt GTA 11250 DSP Manual

5
Zoom out
Zoom in
Previous page
1/32
Next page
GTA 11250 DSP
5
ENGLISH
Warranty
We provide a manufacturer's warranty for products bought
within the European Union. For devices purchased outside
the European Union, the warranty terms issued by our re-
spective responsible domestic agency are valid. The warranty
terms can be called up from www.blaupunkt.com.
Recommendation
The performance of an ampli er can only be as good as
its installation. A correct installation increases the overall
performance of your car sound system. The GTA ampli er
should be installed by a trained person. If you would to install
it yourself, please read these installation instructions very
carefully and allow yourself su cient time for the installation.
In conclusion, allow us a few words about the topic of health
protection:
During the playback of music in your vehicle, please consider
that continuous sound-pressure levels above 100 dB can
lead to permanent damages to the human ear and even to
loss of hearing. Using today's high-performance systems
and loudspeaker con gurations allows for reaching sound-
pressure levels above 130 dB.
Safety notes
Please observe the following safety notes during the instal-
lation and connection.
– Disconnect the negative pole of the battery! Observe the
safety notes of the vehicle manufacturer.
– When you drill holes, ensure that you do not damage any
vehicle components.
– The cross section of the plus and minus cable may not
be less than 10 mm
2
.
– Use cable glands for holes with sharp edges.
– An incorrect installation can result in malfunctions of
the electronic vehicle systems or your car sound system.
Installation and connection instructions
With respect to accident safety, the GTA 11250 DSP must be
secured in a professional way.
When selecting the installation location, select a dry location
that o ers su cient air circulation for cooling the ampli er.
The GTA 11250 DSP must not be installed on rear shelves, rear
seats or other locations that are open to the front.
The installation surface must be suitable to accept the ac-
companying screws and provide a  rm support.
The ampli er power cable must be  tted with a fuse no more
than 30 cm from the battery to protect the vehicle battery in
case of a short circuit between power ampli er and battery.
The fuse of the ampli er protects only the ampli er, not the
vehicle battery.
Only loudspeakers with 2 - 4 Ω impedance may be used
(see table or installation drawings). Observe the maximum
power handling capacity (music output). Do not connect
loudspeakers to earth, use only the referenced terminals.
Audio inputs
The preampli er outputs are connected to the cinch (RCA)
sockets via a shielded audio line (see Fig. 3).
Plus / minus connection
– We recommend a minimum cross section of 10 mm
2
.
– Route commercially available plus cables to the battery
and connect via fuse holder.
– Use cable glands for holes with sharp edges.
– Securely fasten commercially available minus cables to a
noise-free earth point (chassis screw, chassis metal) (not
to the minus pole of the battery).
– Scrap the contact surfaces of the earth point until they
are bright and grease with graphite grease.
Switching on/o
A special feature of the GTA 11250 DSP is its automatic
switch-on.
The ampli er automatically switches on if a music signal
is received. If no music signal is received for more than
60seconds, the GTA 11250 DSP automatically switches o .
Integrated fuses (3 x 30 A)
The fuses integrated in the ampli er protect the power
ampli er and the entire electrical system in case of an error.
If a replacement fuse is used, never bridge fuses or replace
them with a type with higher current.
Connection examples
Connection of the voltage supply ..................................Fig. 2
Audio inputs ...........................................................................Fig. 3 - 4
Loudspeaker connections .................................................Fig. 5
Remote control connection ................................................Fig. 6
Remote connection of the ampli er with switchable +12 V
voltage source.
This allows the ampli er to be switched on and o using the
on/o -switch of the car sound system.
Subwoofer connection
As with every audio component, the correct polarization
of ampli er and loudspeakers is of essentially importance
for a good bass response. For this reason, ensure that the
positive connection (+) of the ampli er is connected with
the positive connection (+) of the loudspeaker; the same
applies to the negative connections (–). In addition, the
left amplifier channel must be connected with the left
loudspeaker and the right ampli er channel with the right
loudspeaker. Positive(+) and negative (–) connections are
wired parallel internally.
GTA_11250_DSP_13LG.indd 5GTA_11250_DSP_13LG.indd 5 26.08.13 09:1226.08.13 09:12
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt GTA 11250 DSP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt GTA 11250 DSP in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info