698854
7
Zoom out
Zoom in
Previous page
1/84
Next page
5
1. Blade
2. Switch (II, 0, I)
3. Blade lock
4. Body
5. Power-cord plug
6. Non-slip feet
7. Sliding-board guide
BEFORE FIRST USE
1. After unpacking, remove the foil and papers protecting the appliance. Then clean the slicer
according to the instructions in the Cleaning and Maintenance section.
2. Place the slicer on a flat top, close to an electrical socket, keeping a distance for convenient access to
the switch and pusher.
3. Turn the thickness adjustment knob to 0 mm.
4. Slide the sliding board into the guide until it locks firmly.
5. Slide the pusher onto the sliding board.
USING THE SLICER
1. Slide the sliding board towards yourself, then position the product ready for slicing on the sliding
board.
2. Set the desired cutting thickness using the adjustment knob.
3. Plug the power cord into the electrical socket.
4. Run the slicer with your left hand by pressing the switch. It is recommended to use the switch in
position I. When the button is released, the slicer switches off. Continuous operation (position II) is
recommended only for advanced users, and requires special care.
5. Slowly move the sliding board towards the blade with the right hand, gently pressing the product
with the pusher. Then move back the sliding board.
6. After the cutting is finished, turn off the appliance with the switch and wait for the blade to stop.
Unplug the power cord from the electric socket. Turn the thickness adjustment knob to 0 mm.
7. Clean the slicer after each use.
CLEANING AND MAINTENANCE
Before cleaning the appliance, make sure that the device is disconnected from the power supply.
Turn the thickness-adjustment knob to 0 mm.
Wipe the slicer body with a slightly damp cloth, then wipe until it is dry. Never immerse the appliance
in water, or wash it under running water.
Blade disassembly
Turn the blade-mounting screw to the right (following the arrow) and unscrew it. Carefully remove the
blade without touching the sharp surfaces.
Clean the blade with water and dishwashing liquid. Before assembly, make sure that it has fully dried
out.
To assemble the blade, insert it while paying attention to the alignment of the sprockets, then screw it
to the left with the mounting screw.
Sliding-board disassembly
Slide the sliding-board lock towards yourself, then slide the sliding board out of the guides.
Clean the blade and the pusher with water and dishwashing liquid.
8. Sliding board
9. Tray
10. Sliding-board handle
11. Thickness-adjustment knob (0-20mm)
12. Size-control board
13. Pusher
FMS501
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt FMS501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt FMS501 in the language / languages: English, German as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info