614187

Blaupunkt EMA 255 Manual

48
Zoom out
Zoom in
Previous page
1/52
Next page
EMA 255
48
Application options and loudspeaker connection
Stereo mode
Max power 2 x 110 W / 4 Ω Fig. 4, 5
Mono mode
Max power 1 x 330 W / 4 Ω Fig. 6
Stereo mode
Max power 2 x 160 W / 2 Ω Fig. 4, 5
Stereo mode
RMS power 2 x 55 W / 4 Ω Fig. 4, 5
Mono mode
RMS power 1 x 165 W / 4 Ω Fig. 6
Stereo mode
RMS power 2 x 80 W / 2 Ω Fig. 4, 5
Frequency response 10 Hz - 30,000 Hz
Signal-to-noise ratio > 85 dB @ RMS power
Signal-to-noise ratio > 75 dB @ 1 W / 1 kHz
Distortion factor (RMS) < 0.08 %
Stability 2 Ω (4 Ω in bridge mode)
Input sensitivity 0.2 - 10 V
Low-pass  lter
(Low Pass) 50 - 250 Hz
High-pass  lter
(High Pass) 80 Hz
Bass boost 0 dB / 6 dB / 12 dB
Dimensions
W x H x D (mm)
W x H x D (")
184 x 52.5 x 183
7.25 x 2.1 x 7.2
Audio inputs (see Fig. 3)
You can select between 2 di erent audio inputs;
Cinch (RCA)
Hi level (loudspeaker connections)
Use only one of the audio inputs; otherwise, it may lead to
audio interferences.
The preampli er outputs are connected to the cinch (RCA)
sockets
1 via a shielded sound cable.
With control via the loudspeaker outputs, the input connec-
tions of pos.
2/3 are fed to the closest loudspeaker cables
(front or rear) on the left and right. They are separated and
connected to the input connections. The polarity of the
+ or - connections must be observed. Bridge output stages
(BTL) can also be connected directly without an additional
adapter.
–
–
Plus / minus connection
We recommend a minimum cross section of 6 mm
2
.
Route commercially available plus cables to the battery
and connect via fuse holder.
Use cable glands for holes with sharp edges.
Securely fasten commercially available minus cables to a
noise-free earth point (chassis screw, chassis metal) (not
to the minus pole of the battery).
Scrap the contact surfaces of the earth point until they
are bright and grease with graphite grease.
Integrated fuses (Fuse)
The fuses integrated in the ampli er (Fuse) protect the power
ampli er and the entire electrical system in case of an error.
If a replacement fuse is used, never bridge fuses or replace
them with a type with higher current.
Connection examples
Connection of the voltage supply ...............................Fig. 2
Audio inputs ....................................................................... Fig. 3
Loudspeaker connections .............................................Fig. 4/5/6
+12V
Remote connection of the ampli er with switchable +12 V
voltage source.
This allows the ampli er to be switched on and o using the
on/o -switch of the radio device.
Level control
The Level control is used to adjust the input sensitivity of
the power ampli er to the output voltage of your car sound
system preampli er output.
The adjustment range is from 0.2 V to 10 V.
If a car sound system of a third party manufacturer is con-
nected, the input sensitivity must be adjusted corresponding
to the manufacturer data.
A few important explanations in this context:
By turning the control clockwise, the input sensitivity of the
ampli er and, therefore, also the volume increases. However,
this is not a volume control; no further ampli er output
can be achieved in the end position, even if it may sound
like that at the beginning. The system merely increases the
volume faster if the volume control of the car sound system
is turned up.
Loudspeaker connections
(If the ampli er is to be jumpered, continue with the section
"Bridged loudspeaker connections" at this point).
As with every audio component, the correct polarisation of
ampli er and loudspeakers is of essentially importance for a
good bass response. For this reason, ensure that the positive
(+) connection of the ampli er is connected with the posi-
tive connection (+) of the loudspeaker; the same applies to
the negative (-) connections. In addition, the left ampli er
channel must be connected with the left loudspeaker and
the right ampli er channel with the right loudspeaker.
–
–
–
–
–
EMA_255_22LG.indd 48EMA_255_22LG.indd 48 20.02.2013 10:55:04 Uhr20.02.2013 10:55:04 Uhr
… 48 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt EMA 255 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt EMA 255 in the language / languages: All languages as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info