614187

Blaupunkt EMA 255 Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
EMA 255
6
Plus / minus connection
We recommend a minimum cross section of 6 mm
2
.
Route commercially available plus cables to the battery
and connect via fuse holder.
Use cable glands for holes with sharp edges.
Securely fasten commercially available minus cables to a
noise-free earth point (chassis screw, chassis metal) (not
to the minus pole of the battery).
Scrap the contact surfaces of the earth point until they
are bright and grease with graphite grease.
Integrated fuses (Fuse)
The fuses integrated in the ampli er (Fuse) protect the power
ampli er and the entire electrical system in case of an error.
If a replacement fuse is used, never bridge fuses or replace
them with a type with higher current.
Connection examples
Connection of the voltage supply ...............................Fig. 2
Audio inputs ....................................................................... Fig. 3
Loudspeaker connections .............................................Fig. 4/5/6
+12V
Remote connection of the ampli er with switchable +12 V
voltage source.
This allows the ampli er to be switched on and o using the
on/o -switch of the radio device.
Level control
The Level control is used to adjust the input sensitivity of
the power ampli er to the output voltage of your car sound
system preampli er output.
The adjustment range is from 0.2 V to 10 V.
If a car sound system of a third party manufacturer is con-
nected, the input sensitivity must be adjusted corresponding
to the manufacturer data.
A few important explanations in this context:
By turning the control clockwise, the input sensitivity of the
ampli er and, therefore, also the volume increases. However,
this is not a volume control; no further ampli er output
can be achieved in the end position, even if it may sound
like that at the beginning. The system merely increases the
volume faster if the volume control of the car sound system
is turned up.
Loudspeaker connections
(If the ampli er is to be jumpered, continue with the section
"Bridged loudspeaker connections" at this point).
As with every audio component, the correct polarisation of
ampli er and loudspeakers is of essentially importance for a
good bass response. For this reason, ensure that the positive
(+) connection of the ampli er is connected with the posi-
tive connection (+) of the loudspeaker; the same applies to
the negative (-) connections. In addition, the left ampli er
channel must be connected with the left loudspeaker and
the right ampli er channel with the right loudspeaker.
–
–
–
–
–
Bridged loudspeaker connections
The EMA ampli er can also be bridged for a mono con gura-
tion. This allows the ampli er to be used for one or several
subwoofers or mid-range drivers. In this con guration, the
ampli er combines the right and left channel to a single-
channel output (mono output).
Note:
The ampli er can add the right and left signal information
only if the right as well as the left RCA connection were
carried out.
Caution:
In a bridge circuit, the ampli er load must be 4 ohm or
higher. A lower load leads to an overheating or switch-o
of the ampli er and can cause permanent damages.
Adjusting the type and range of the
frequency crossovers
With the EMA 255, the type of frequency crossover (i.e. "Low
Pass" or "Hi-Pass") and the desired entry frequency can be
adjusted. For example, if a pair of subwoofers is to be con-
nected, the low-pass settings shown are required (Fig. 3). The
entry frequency is dependent upon the frequency range of
the loudspeakers (see recommended frequency range of
the loudspeakers).
High-Pass
At a setting of 80 Hz, the ampli er has a frequency range of
80 Hz to 30,000 Hz.
Low-pass frequency control
This control is active if the switch is in the position "Low-Pass",
and allows for setting the desired entry frequency.
Example:
At a setting of 150 Hz, the ampli er has a frequency range
of 10 Hz to 150 Hz.
Bass boost
The bass boost control is used to adjust the bass response
of the ampli er.
The setting options are: 0 dB / +6 dB / +12 dB.
Power-on indicator (PWR / PRO)
Green LED:
Output stage on, regular operating status.
Red LED:
Output stage is electronically switched o due to an error.
Recycling and disposal
Please use the return and collection systems avail-
able to dispose of the product.
Subject to changes
EMA_255_22LG.indd 6EMA_255_22LG.indd 6 20.02.2013 10:54:55 Uhr20.02.2013 10:54:55 Uhr
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt EMA 255 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt EMA 255 in the language / languages: All languages as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info