614231

Blaupunkt BX-S1 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
1. Use the 4 mounting holes on the back to mark position on the
wall.
2. Drill holes into the wall using the mounting holes as template.
3. Fix the base onto the wall with the screw and plugs provided.
4. Replace the front cover onto the base.
5. Enable the Siren Tamper function on you Control Panel.
When mounting the Bell Box, please take note of the following
points:
Mount on the external wall at a prominent location.
Mount as high as possible out of easy reach.
T
T
a
a
m
m
p
p
e
e
r
r
S
S
w
w
i
i
t
t
c
c
h
h
The Bell Box is protected by a tamper switch which will be
activated if the Bell Box is removed from the mounted location, or
its cover opened. When installing the Bell Box, please make sure
the tamper switch is properly compressed against the wall, and
the front cover is secured with screw.
Before installing the Bell Box, changing mounting location or
batteries, please make sure to disable the tamper switch
temporarily using your Control Panel’s Siren Tamper function and
enable the tamper switch again after finish working on the Bell
Box. Please refer to your Control Panel manual for detail.
S
S
i
i
r
r
e
e
n
n
A
A
u
u
d
d
i
i
b
b
l
l
e
e
P
P
e
e
r
r
f
f
o
o
r
r
m
m
a
a
n
n
c
c
e
e
The siren produces a minimum of 104 dBA sound pressure at 1
meter range when activated.
For Burglar and Panic Alarm, the Bell Box gives a continuous
alarm sound.
For Fire / Water alarm, the Bell Box gives an intermittent alarm
sound of 2-sec siren followed by a 1 sec interval.
The siren is silenced when either the programmed siren length
expires or when the Control Panel is disarmed to turn off the siren.
Please refer to Dip Switch table above to set your desired alarm
length through Dip Switch SW3 and SW4 setting.
S
S
t
t
r
r
o
o
b
b
e
e
(
(
L
L
E
E
D
D
)
)
L
L
i
i
g
g
h
h
t
t
When the Bell Box is activated, the LED strobe light will also flash
to indicate the Bell Box is alarming. The duration of strobe light
flash is determined by Dip Switch SW2 setting. When set to OFF,
the strobe light will flash according to the alarm length set by Dip
Switch SW3 and SW4. When set to ON, the strobe light will flash
after the alarm length has expired until the control panel is
disarmed.
Audio & Visual Status Indication Table
The Bell Box will activate its siren and strobe light to notify the
user of system status, please refer to below table.
* Siren Audio indication will be effected by the Confirmation ON /
OFF setting in your Control Panel settings.
B
B
a
a
t
t
t
t
e
e
r
r
y
y
The Bell Box uses four 1.5V D alkaline batteries as its power
source. It also features low battery detection function to notify the
Control Panel when battery voltage is low.
When the Bell box is on low battery, follow the procedure below
to change the batteries.
1. Temporarily disable the Bell Box’s tamper protection function
(please refer to your Control Panel manual for detail). The Bell
Box will sound a beep to indicate the tamper is disabled.
2. Remove the front cover.
3. Remove the four screws fixing the battery compartment and
take off the compartment lid.
4. Remove the old batteries and press the Tamper Switch twice to
discharge.
5. Insert the new D cell alkaline batteries into the battery
compartment according to correct polarity.
6. The Bell Box will emit beeps and flash when the last battery is
inserted.
7. Replace the battery compartment lid and front cover
8. Enable the tamper protection function through your Control
Panel. The Bell Box will sound a beep to indicate.
E
E
n
n
v
v
i
i
r
r
o
o
n
n
m
m
e
e
n
n
t
t
a
a
l
l
C
C
o
o
n
n
d
d
i
i
t
t
i
i
o
o
n
n
-10°C to 40°C, relative humidity 85% non-condensing.
R
R
a
a
d
d
i
i
o
o
433 MHz
F
F
C
C
C
C
S
S
t
t
a
a
t
t
e
e
m
m
e
e
n
n
t
t
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
F
F
C
C
C
C
C
C
a
a
u
u
t
t
i
i
o
o
n
n
:
:
To assure continued compliance, any changes or modifications
not expressly approved by the party responsible for compliance
may void the user's authority to operate this equipment. (Example
- use only shielded interface cables when connecting to computer
or peripheral devices).
S
S
i
i
r
r
e
e
n
n
A
A
u
u
d
d
i
i
o
o
S
S
t
t
r
r
o
o
b
b
e
e
l
l
i
i
g
g
h
h
t
t
i
i
n
n
d
d
i
i
c
c
a
a
t
t
i
i
o
o
n
n
Arm/Home 1 beep*
3 LED flashes at
once
Disarm 2 beeps*
Sequentially
flashes for 1 cycle
Arm (Low Battery) 5 beeps
3 LED flashes for
three times
Disarm (Low
Battery)
5 beeps
Sequentially
flashes for 2 cycles
Arm (Tamper) 5 beeps
3 LED flashes for
three times
Disarm (Tamper) 2 beeps*
Sequentially
flashes for 2 cycles
Previous alarm
warning
3 sec beep
Sequentially
flashes for 2 cycles
Tamper Alarm Continuous beeps
Sequentially
flashes
Entry/Exit Sound Count-down beeps None
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
S
S
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt BX-S1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt BX-S1 in the language / languages: English as an attachment in your email.

The manual is 0,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blaupunkt BX-S1

Blaupunkt BX-S1 User Manual - German - 2 pages

Blaupunkt BX-S1 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info