163352

Blaupunkt bremen mp74 Manual

17
Zoom out
Zoom in
Previous page
1/20
Next page
- 5 -
D
E
B
A C
3. Display Frequency Response Cutoff Filter
In diesem Bild können Sie Einstellungen an diversen Filtern
vornehmen und Filtereinstellungen anzeigen. Die vorgenomme-
nen Einstellungen werden grafisch dargestellt.
A. Center
Mit den Einstellungen unter Center beeinflussen Sie den Klang
Ihres Center-Lautsprechers.
Durch Klicken der Pfeilsymbole < > oder durch Verschieben
des Reglers "Highpass Filter" variieren Sie die Grenzfrequenz
des Hochpassfilters (Filter 2. Ordnung, 12dB/Oktave) zwischen
200 und 3200 Hz. Mit "Gain" können Sie den Pegel des Aus-
gangs um +/- 6 dB verändern.
Wenn Sie "flat" angeklickt haben, werden alle Frequenzen ohne
Filterwirkung vom Centerlautsprecher wiedergegeben.
Die Anzeige der geänderten Werte erfolgt durch einen Maus-
klick auf "Center"
B. Subwoofer
Mit den Einstellungen unter Subwoofer verändern Sie den
Klang Ihres angeschlossenen Subwoofers.
Durch Klick auf < > oder Schieben des Reglers "Gain" können
Sie die Verstärkung zwischen +/- 6 dB einstellen. Mit "Phase"
stellen Sie die Phasenlage zwischen - 135 und + 180 Grad in
45 Grad-Schritten ein.
Um extrem tieffrequente Anteile von kleinen Subwoofern
fernzuhalten, können Sie zusätzlich ein Subsonic-Filter (Filter 2.
Ordnung, 12 dB/Oktave) einschalten. Die Einstellung erfolgt
durch Klick auf < > oder Schieberegler "Cutoff Freq." zwischen
20 und 40 Hz. Mit "Q Factor" können sie die Güte des Sub-
sonic-Filters von 0,5 - 1,3 variieren.
Durch einen Mausklick auf "flat" wird das Subsonic-Filter
ausgeschaltet.
Mit dem Lowpass Filter (Filter 4. Ordnung, 24 dB/Oktave)
können Sie die obere Grenzfrequenz einstellen, bis zu der der
Subwoofer arbeiten soll. Dies erfolgt durch Klick auf < > oder
Verschieben der Frequenz von 40 - 100 Hz. Mit dem Mausklick
auf "Flat" wird das Filter ausgeschaltet und alle Frequenzen
vom Subwoofer wiedergegeben.
Die Anzeige der geänderten Werte erfolgt durch einen Maus-
klick auf "Subwoofer".
C. Front / Rear
Unter Front / Rear können Sie ein Hochpassfilter (Filter 2.
Ordnung, 12 dB/Oktave) für die vorderen oder hinteren Kanäle
separat einstellen. Damit erreichen Sie, dass diese nur die
Frequenzen wiedergeben, die vom angeschlossenen
Subwoofer nicht verarbeitet werden.
3. Display showing the frequency response cut-off filter
On this screen you can make changes to various filters and
display the filter settings. The configured settings are
displayed graphically.
A. Center
You can adjust the sound of your centre loudspeaker using the
settings in the Center section. You can adjust the cut-off
frequency of the highpass filter (2nd order filter, 12 dB/octave)
between 200 and 3200 Hz by clicking on the arrow symbols < >
or by adjusting the „Highpass Filter“ slider control. „Gain“ allows
you to change the level of the output by +/- 6 dB.
If you clicked on „flat“, all the frequencies will be reproduced by
the centre loudspeaker without a filter effect. Clicking with the
mouse on „Center“ will cause the changed values to be
displayed.
B. Subwoofer
You can adjust the sound of your connected subwoofer using
the settings in the Subwoofer section. You can set the
amplification to between +/- 6 dB by clicking on < > or sliding
the „Gain“ control. „Phase“ allows you to set the phase to
between -135 and + 180 degrees in 45-degree steps.
In order to keep extremely low-frequency sound components
away from small subwoofers, you can additionally activate a
subsonic filter (2nd order filter, 12 dB/octave). You can set a
value between 20 and 40 Hz by clicking on < > or adjusting the
„Cutoff Freq.“ slider control. „Q Factor“ allows you to change the
quality factor of the subsonic filter to a value between 0.5 - 1.3.
Clicking with the mouse on „flat“ deactivates the subsonic filter.
The lowpass filter (4th order filter, 24 dB/octave) allows you to
specify the upper cut-off frequency - the subwoofer will then
operate only up to this frequency. You adjust this by clicking on
< > or sliding the frequency control between 40-100 Hz. Clicking
with the mouse on „flat“ deactivates the filter and all the
frequencies will then be reproduced by the subwoofer.
Clicking with the mouse on „Subwoofer“ will cause the changed
values to be displayed.
C. Front / Rear
In the Front / Rear section, you can adjust the highpass filter
(2nd order filter, 12 dB/octave) separately for the front or rear
channels. This allows you to make sure that they only
reproduce the frequencies that are not processed by the
connected subwoofer.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt bremen mp74 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt bremen mp74 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blaupunkt bremen mp74

Blaupunkt bremen mp74 User Manual - Dutch - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info