Manual Blaupunkt BHKA 754101 (page 14 of 20) (English, German)

716217

Zoom out

Zoom in

1/20

Two Speed Gear Setting

The drill is ﬁtted with a 2 speed gear system allowing for high and low drilling speeds. To set the speed use the slider switch on the

top of the drill.

• Use the low (1) speed for high power and torque applications.

• Use the high (2) speed for low power fast drilling applications.

• Do not attempt to adjust the speed setting while the drill is in use otherwise the gears will be damaged.

Drilling (Wood and other soft materials)

• If drilling in a small workpiece, make sure it is securely held in a vice or clamped to a secure platform such as a bench or table.

• Install the correct drill bit in the chuck. Rotate the chuck body to loosen or tighten the drill bit in the chuck. Never use the drill’s

power to rotate the chuck body.

• Select the rotation direction to clockwise using the button located above the trigger switch.

• Select the correct transmission speed. Use the slower speed for drilling large holes.

• Set the torque adjusting collar to the drilling position (Fig.2 (3)).

• Slide the fully charged battery pack onto the base of the handle.

• Mark the drilling point with a centre punch when drilling in metal to prevent the drill bit from slipping oﬀ centre as you begin

drilling.

• Place the drill bit at the location of the hole to be drilled and squeeze the trigger. The harder you squeeze, the faster the drill

turns.

Drilling (Masonry)

• Follow drilling instructions as above but adjust the collar to the hammer position (Fig.2 (4))

• Use only drill bits suitable for masonry.

• It is not recommended to use the hammer setting when drilling into wall and ﬂoor tiles as this may cause them to crack or

shatter, instead use a specialist bit and use the standard drilling function as above.

Driving Screws

Suggested Torque Settings

1-4 Driving small screws

5-8 Driving medium size screws into soft materials

9-14 Driving screws into soft and medium-density materials

15-21 Driving screws into hardwood

• Install the correct screwdriver bit in the chuck. Use the largest bit size that will properly that the screw. Make sure the that

sides of the bit are gripped by the chuck.

• Set the transmission speed to low speed.

• Set the rotation directions to clockwise.

• Set the torque collar desired setting (Fig.1(1))

• Place the screwdriver bit into the screw and hold the bit ﬁrmly into the screw to prevent slippage and drive a test screw.

• After driving a test screw, adjust the torque setting up or down so the screw is driven to the desired depth without being over

driven.

• Release the trigger immediately when the torque clutch begins to ‘rattle’.

• Screws can be removed by reversing the direction of the rotation.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt BHKA 754101 in the language / languages: English, German as an attachment in your email.

The manual is 0,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blaupunkt BHKA 754101 Manual

Product: