Manual Blaupunkt 5DK69450 (page 23 of 52) (English, German, Dutch, French)

614177

Zoom out

Zoom in

1/52

General information

Exhaust air mode

: Risk of death!

Risk of poisoning from flue gases that are drawn back in. The

exhaust air must not be conveyed into a functioning smoke or

exhaust gas flue or into a shaft which is used to ventilate

installation rooms that contain heating appliances. If the

exhaust air is to be conveyed into a non-functioning smoke or

exhaust gas flue, you must obtain the consent of the heating

engineer responsible.

If the exhaust air is conveyed through the outer wall, a

telescopic wall box should be used.

Exhaust duct

Note: The device manufacturer does not assume any warranty

for complaints attributable to the pipe section.

■ The device achieves its optimum performance by means of a

short, straight exhaust air pipe and as large a pipe diameter

as possible.

■ As a result of long rough exhaust air pipes, many pipe bends

or pipe diameters that are smaller than 150 mm, the optimum

extraction performance is not achieved and fan noise is

increased.

■ The pipes or hoses for laying the exhaust air line must

consist of non-combustible material.

Round pipes

An inner diameter of 150 mm, but at least 120 mm, is

recommended.

Flat ducts

The inner cross-section must correspond to the diameter of the

round pipes.

dia. 150 mm ca. 177 cm

dia. 120 mm ca. 113 cm

■ Flat ducts should not have any sharp deflections.

■ Use sealing strips for deviating pipe diameters.

Checking the wall

■ The wall must be level, vertical and adequately load-bearing.

■ The depth of the bore holes must be the same length as the

screws. The wall plugs must have a secure grip.

■ The enclosed screws and wall plugs are suitable for solid

brickwork. Suitable fasteners must be used for other

structures (e.g. plasterboard, porous concrete, poroton

bricks).

■ The max. weight of the extractor hood is 40 kg.

Electrical connection

: Risk of electric shock!

Components inside the appliance may have sharp edges.

These may damage the connecting cable. Do not kink or pinch

the connecting cable during installation.

The required connection data can be found on the rating plate

inside the appliance; to do this, remove the metal mesh grease

filter.

Length of the cable: approx. 1.30 m

This appliance complies with the EC interference suppression

regulations.

: Risk of electric shock!

It must always be possible to disconnect the appliance from the

electricity supply. The appliance must only be connected to a

protective contact socket which has been correctly installed. If

the plug is no longer accessible following installation of the

appliance, or a fixed connection is required, an all-pole isolating

switch must be present on the installation side with a contact

gap of at least 3 mm. The fixed connection must only be

installed by an electrician.

Installation

Preparing the installation

Caution!

Ensure that there are no electric wires, gas or water pipes in the

area where holes are to be made.

1. Mark a vertical centre line on the wall from the ceiling to the

lower edge of the extractor hood.

2. Mark positions for the screws and the contour of the

attachment area.

3. Drill five 8 mm Ø holes to a depth of 80 mm for the

attachments and press in the wall plugs flush with the wall.

[

PP

PP

PP

PP

PP

PLQPP

PD[PP

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt 5DK69450 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blaupunkt 5DK69450 Manual

Product: