577915
8
Zoom out
Zoom in
Previous page
1/84
Next page
8
ENGLISH
Fitting the distance piece (fig. E)
Fit the distance piece (14) to the base of the router using
the screws provided.
Fitting the centring pin (fig. F)
Fit the edge guide to the router as shown in fig. B,
but upside down.
Fit the centring pin (15) to the workpiece side of the edge
guide with the screw (25) provided.
Fitting the copy follower (fig. G)
Fit the edge guide to the router as shown in fig. B.
Fit the ‘L’ bar (16) to the upper side of the edge guide
using the two screws and nuts provided.
Adjust the rotating attachment (26) on the ‘L’ bar with the
wing knob (27).
Fitting the additional edge guide (fig. H)
The additional guide (21) is designed to allow routing of a thin
piece of wood (e.g. the edge of a door).
Adjust the edge guide (12) as necessary.
Loosen the fixing screws (28).
Fit the edge guide (21) to the bars (19) protruding from the
router base.
Adjust the edge guide so the workpiece becomes clamped
between the two edge guide.
Tighten the fixing screws (28).
Use
Warning! Let the tool work at its own pace. Do not overload.
Carefully guide the cable in order to avoid accidentally
cutting it.
Adjusting the depth of cut (fig. I, J & K)
The depth of cut is the distance X between the depth stop bar
(9) and the depth stop (29). The depth of cut can be set in two
different ways as described below.
Adjusting the depth of cut using the scale (fig. J)
Fit the router bit as described above.
Loosen the locking screw (30).
Pull the plunge lock lever (5) up.
Plunge the router down until the router bit touches the
workpiece.
Push the plunge lock lever (5) down.
Move the depth stop bar (9) down against the depth stop
using the depth stop adjuster (31). Reset the scale by
aligning the zero marking (32) with the arrow (33).
Move the depth stop bar (9) to the calculated position
using the depth stop adjuster (31). One quarter turn
corresponds to approx. 6.25 mm.
Tighten the locking screw (30).
Fine adjust using the adjusting knob (34). One full turn
corresponds to approx. 1 mm.
Pull the plunge lock lever (5) up and return the router to its
original position.
After switching the router on, plunge it down and make
the desired cut.
Adjusting the depth of cut using a piece of wood (fig. K)
Fit the router bit and plunge the router down as described
above.
Loosen the locking screw (30).
Move the depth stop bar (9) up using the depth stop
adjuster (31).
Place a piece of wood with a thickness equal to the
desired depth of cut between the depth stop (29) and the
depth stop bar (9).
Move the depth stop bar (9) down against the wood using
the depth stop adjuster (31).
Tighten the locking screw (30).
Fine adjust using the adjusting knob (34).
Remove the piece of wood.
Pull the plunge lock lever (5) up and return the router to its
original position.
After switching the router on, plunge it down and make
the desired cut.
Adjusting the revolver depth stop (fig. L)
After turning the revolver depth stop to the desired setting,
you can fine-adjust the depth stop to be used. If you want to
make several cuts with a different depth of cut, adjust each of
the depth stops.
Turn the depth stop screw (35) up or down as required
using a screwdriver.
Setting the speed
Set the speed control knob (4) to the required speed.
Use a high speed for small diameter router bits. Use a low
speed for large diameter router bits.
Using a batten as a guide (fig. M)
When it is not possible to use the edge guide, for example
when routing grooves in the back panel of a bookcase to
support shelves, proceed as follows:
Select a piece of wood with a straight edge to use as a
batten.
Place the batten onto the workpiece.
Move the batten until it is in the correct position to guide
the tool.
Securely clamp the batten to the workpiece.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker XTW1500E T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker XTW1500E T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info