579752
6
Zoom out
Zoom in
Previous page
1/84
Next page
6
ENGLISH
Safety instructions for saws with a pendulum blade guard
Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does not
move freely and close instantly. Never clamp or tie
the lower guard into the open position. If saw is
accidentally dropped, lower guard may be bent. Raise the
lower guard with the retracting handle and make sure it
moves freely and does not touch the blade or any other
part, in all angles and depths of cut.
Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use. Lower
guard may operate sluggishly due to damaged parts,
gummy deposits, or a build-up of debris.
Lower guard should be retracted manually only for
special cuts such as “plunge cuts” and “compound
cuts.” Raise lower guard by retracting handle and
as soon as blade enters the material, the lower
guard must be released. For all other sawing, the lower
guard should operate automatically.
Always observe that the lower guard is covering
the blade before placing saw down on bench or
floor. An unprotected, coasting blade will cause the saw
to walk backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade to stop after
switch is released.
Additional safety instructions for all saws with riving knife
Use the appropriate riving knife for the blade being
used. For the riving knife to work, it must be thicker than
the body of the blade but thinner than the tooth set of the
blade.
Adjust the riving knife as described in this
instruction manual. Incorrect spacing, positioning and
alignment can make the riving knife ineffective in preventing
kickback.
Always use the riving knife except when plunge
cutting. Riving knife must be replaced after plunge
cutting. Riving knife causes interference during plunge
cutting and can create kickback.
For the riving knife to work, it must be engaged in
the workpiece. The riving knife is ineffective in
preventing kickback during short cuts.
Do not operate the saw if riving knife is bent. Even a
light interference can slow the closing rate of a guard.
Additional safety instructions for circular saws
Wear ear protectors. Exposure to noise can cause hearing
loss.
Preferably wear a dust mask.
Do not use blades of larger or smaller diameter than
recommended. For the proper blade rating refer to the
technical data. Use only the blades specified in this
manual, complying with EN 847-1.
Never use abrasive cut-off wheels.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Overview
1. On/off switch
2. Lock-off button
3. Main handle
4. Secondary handle
5. Spindle lock button
6. Shoe
7. Saw blade
8. Saw blade guard
9. Riving knife
10. Parallel fence
11. Laser unit
12. Saw blade spanner
13. Dust extraction outlet
Assembly
Warning! Before assembly, make sure that the tool is switched
off and unplugged and that the saw blade has stopped.
Removing and fitting a saw blade (fig. A)
Removing
Keep the spindle lock button (5) depressed and rotate the
blade until the spindle lock engages.
Loosen and remove the blade retaining screw (14) by turning
it counterclockwise using the spanner (12) supplied.
Remove the outer washer (15).
Remove the saw blade (7).
Fitting
Place the saw blade onto the inner flange (16), making
sure that the arrow on the blade points in the same
direction as the arrow on the tool.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker XTS1660KA T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker XTS1660KA T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker XTS1660KA T1

Black Decker XTS1660KA T1 Quick start guide - English - 12 pages

Black Decker XTS1660KA T1 User Manual - Polish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info