581131
5
Zoom out
Zoom in
Previous page
1/64
Next page
5
ENGLISH
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Additional safety instructions for jigsaws
Warning! Contact with or inhalation of dusts arising
from cutting applications may endanger the health of the
operator and possible bystanders. Wear a dust mask
specifically designed for protection against dust and
fumes and ensure that persons within or entering the
work area are also protected.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-on button
3. Variable speed control knob
4. Mode selector switch
5. Saw blade locking lever
6. Saw blade holder
7. Shoe plate
8. Shoe plate locking knob
9. Scroll knob
10. Saw blade storage compartment
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and
that the saw blade has stopped. Used saw blades can be hot.
Fitting the saw blade (fig. A)
Hold the saw blade (11) as shown, with the teeth facing
forward.
Push the lever (5) downwards.
Insert the shank of the saw blade into the blade holder (6)
as far as it will go.
Release the lever.
Adjust the blade support roller as described below.
Adjusting the blade support roller (fig. A & B)
After fitting the blade, you need to adjust the blade support
roller (12).
Turn the blade support adjustment screw (13) in the
counterclockwise direction.
Slide the blade support roller against the rear of the blade.
The blade must locate in the central recess of the roller.
Turn the blade support adjustment screw in the clockwise
direction to lock the blade support in place.
Connecting a vacuum cleaner to the tool (fig. C & D)
Align the dust extraction adaptor (14) with the saw shoe
as shown.
Insert the ribs (15) into the slots (16).
Push the adaptor backwards to lock it in position.
Connect the vacuum cleaner hose (17) (not supplied) to
the adaptor.
Dust extraction is not possible when making bevel cuts.
Warning! Do not use the dust extraction adaptor when
sawing metal.
Use
Warning! Never use the tool when the saw shoe is loose or
removed.
Adjusting the shoe plate for bevel cuts (fig. E)
The shoe plate can be set to a left or right bevel angle of up to
45°.
Turn the locking knob (8) in direction A to release the shoe
plate (7).
Pull the shoe plate (7) backwards and set it to the
required angle. You can use the scale or a protractor to
check the angle.
Turn the locking knob (8) in direction B to lock the shoe
plate in place.
To reset the shoe plate for straight cuts:
Turn the locking knob (8) in direction A to release the shoe
plate (7).
Pull the shoe plate backwards and set it to an angle of
approx. 0°.
Push the shoe plate forward.
Turn the locking knob (8) in direction B to lock the shoe
plate in place. Make sure that the shoe plate is supported
by the guide ribs.
Setting the operating mode (fig. F)
In the straight cutting mode, the saw blade can be set and
locked in 4 positions: forward, reverse, left or right.
Turn the mode selector switch (4) to position A (scrolling
mode).
Rotate the saw blade into the required direction using the
scroll knob (9).
Turn the mode selector switch (4) to position B (straight
cutting mode). In this position the scroll knob cannot be
rotated. The saw blade is locked in its position.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker XTS10EK T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker XTS10EK T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker XTS10EK T1

Black Decker XTS10EK T1 Quick start guide - English - 12 pages

Black Decker XTS10EK T1 User Manual - Polish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info