Manual Black Decker XTS100 T1 (page 7 of 12) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

578657

Zoom out

Zoom in

1/12

Labels on tool

The following pictograms are shown on the tool:

Wear ear protectors.

Wear a dust mask.

Features

1. On/off switch

2. Operating handle

3. Rear lower guard

4. Saw arm lock-down knob

5. Angle position stop

6. Vertical position adjustment stop

7. Right-hand fence

8. Hand indentation

9. Mitre scale

10. Mitre latch

11. Mitre clamp knob

12. Left-hand fence

13. Saw blade

14. Moveable lower guard

15. Spindle lock button

16. Saw arm lock-up release lever

Fig. A

17. Motor housing

18. Kerf plate

19. Bench mounting holes

20. Upper fence clamping knob

21. Upper fence adjustment knob

22. Bevel position adjustment stop

23. Bevel scale

24. Bevel clamp knob

25. Saw dust outlet

26. Upper guard

27. Blade spanner

Assembly

Warning! Before assembly, make sure that the tool is switched off and unplugged.

Unpacking (fig. B)

◆ Carefully remove the tool from the packing material.

◆ Press down the operating handle (2) and pull out the lock-down knob (4), as shown.

◆ Gently release the downward pressure and allow the arm to rise to its full height.

◆ Fit the mitre clamp knob (11) as shown

Bench mounting (fig. C)

The feet are provided with holes (19) to facilitate bench mounting.

◆ Pass a bolt through each of the feet and tighten each bolt into a pre-drilled hole in the

work bench. The two different sizes of holes accommodate different sizes of bolts.

Use either hole; it is not necessary to use both. Always mount the machine firmly to

prevent movement.

◆ To enhance the portability, mount the tool to a piece of 12.5 mm or thicker plywood. In

this case it is possible to clamp the machine to your work support or move it to other

job sites and reclamp it there.

◆ When mounting the machine to a piece of plywood, make sure that the mounting

screws do not protrude from the bottom of the wood. The plywood must sit flush on

the work support. When clamping the machine to any work surface, clamp only on the

clamping bosses where the mounting screw holes are located. Clamping at any other

point will interfere with the proper operation of the machine.

◆ To prevent binding and inaccuracy, be sure the mounting surface is not warped or

otherwise uneven. If the machine rocks on the surface, place a thin piece of material

under one foot until the machine is firm on the mounting surface.

Removing and fitting a saw blade (fig. D1 - D5)

Removing

◆ Depress the lever (16) to release the lower guard (14).

◆ Raise the lower guard as far as possible.

◆ Loosen the guard bracket screw (28) to release the angled corner piece (29).

◆ Push the angled corner piece between the head of the screw and the guard.

This allows the guard bracket (30) to be raised enough to permit access to the blade

screw (31).

◆ With the lower guard (14) held in the raised position by the guard bracket screw

depress the spindle lock button (15) and rotate the blade until the lock engages.

◆ While keeping the spindle lock button depressed, loosen and remove the blade screw

(31) by turning it clockwise using the spanner (27) supplied.

◆ Remove outer washer (33).

◆ Remove the saw blade (13).

Fitting

◆ Install the saw blade (13) onto the axle against the inner washer (34). Make sure that

the arrow on the blade points in the same direction as the arrow on the tool.

◆ Replace the outer washer (33).

◆ While keeping the spindle lock button depressed, tighten the blade screw (31) by

turning it counterclockwise using the spanner (27) supplied.

◆ Move the guard bracket (30) down until the angled corner piece (29) is below the head

of the guard bracket screw (28).

◆ Tighten the guard bracket screw.

Warning! Never press the spindle lock while the blade is rotating.

Checking and adjusting the blade to the fence (fig. E1 - E3)

◆ Loosen the mitre clamp knob (11).

◆ Press the mitre latch (10) to release the mitre arm (34).

◆ Adjust the mitre angle to 0°.

◆ Pull down the saw arm until the blade just enters the saw kerf (18).

◆ Place a square (35) against the left-hand fence (12) and the blade (13). Make sure that

the teeth of the blade do not touch the square.

◆ Check the position of the mitre arm (34). If necessary, adjust the mitre arm until the

blade is at 90° to the fence as measured with the square.

◆ Tighten the mitre clamp knob.

◆ Adjust the mitre pointer as necessary.

Adjusting the mitre pointer (fig. E4)

◆ Observe the pointer (36) and the scale (9).

◆ If the pointer does not indicate exactly zero, loosen the screw (37), move the plastic

moulding (38) to read 0° and tighten the screw.

Checking and adjusting the blade to the table (fig. F1 - F3)

◆ Loosen the bevel clamp knob (24).

◆ Adjust the bevel angle to 0°. Move the saw arm to the right until the angle position

stop (5) rests against the stop screw (39).

◆ Pull down the saw arm until the blade just enters the saw kerf (18).

◆ Place a square (35) against the table (12) and the blade (13). Make sure that the teeth

of the blade do not touch the square.

◆ Check the position of the saw arm. If necessary, adjust the saw arm until the blade is

at 90° to the table as measured with the square.

– Loosen the lock nut (39) a few turns.

– Turn the stop screw (6) in or out as required.

– Tighten the lock nut (39).

◆ Tighten the bevel clamp knob.

◆ Adjust the bevel pointers as necessary.

Adjusting the bevel pointers (fig. F4)

◆ Observe the pointer (40) and the scale (23).

◆ If the pointer does not indicate exactly zero, loosen the screw (41) that secures the

pointer and move the pointer as necessary.

◆ Adjust the other pointer (42) according the the same instructions.

Checking and adjusting the bevel angle (fig. G)

◆ Slide the upper part of the left-hand fence (12) out of the way.

◆ Loosen the bevel clamp knob (24).

◆ Adjust the bevel angle to 45°. Move the saw arm to the left until the bevel position

stop (43) rests against the stop screw (22).

◆ Check the position of the saw arm. If necessary, adjust the saw arm until the blade is

at 45°.

– Loosen the lock nut (44) a few turns.

– Turn the stop screw (22) in or out as required.

– Tighten the lock nut (44).

◆ Tighten the bevel clamp knob.

◆ To achieve a 47° left bevel or a 2° right bevel, adjust the stop screw (6 or 22) to allow

the arm to move as necessary.

Adjusting the upper fence (fig. H)

The upper part of the left-hand fence (12) can be adjusted to provide clearance for the

setting of bevel angles.

◆ Loosen the clamping knob (20) and the adjustment knob (21).

◆ Slide the fence to the left.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker XTS100 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker XTS100 T1

Black Decker XTS100 T1 User Manual - Polish - 56 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker XTS100 T1 Manual

Product: