Manual Black Decker xtc 143 bk (page 6 of 80) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

388359

Zoom out

Zoom in

1/80

ENGLISH

3. Chuck

4. Mode selector / torque adjustment collar

5. Three-gear selector

6. Bit holder

7. Battery

8. Side handle

Fig. A

9. Charger

10. Charging indicator

11. End of charge indicator

Assembly

Warning! Before assembly, remove the battery from the tool.

Fitting and removing the battery (fig. B)

◆ To fit the battery (7), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

◆ To remove the battery, push the release button (12) while

at the same time pulling the battery out of the receptacle.

Fitting the battery cap (fig. C)

Warning! Fit the cap (13) to the battery (7) for transportation

and storage.

Fitting the side handle

◆ Loosen the side handle (8) by turning it counterclockwise.

◆ Slide the side handle over the chuck and onto the

housing.

◆ Tighten the side handle by turning it clockwise.

Fitting and removing a drill bit or screwdriver bit (fig. D)

This tool is fitted with a keyless chuck to allow for an easy

exchange of bits.

◆ Lock the tool by setting the forward/reverse slider (2) to

the centre position.

◆ Open the chuck by turning the sleeve (14) with one hand

while holding the tool with the other.

◆ Insert the bit shaft (15) into the chuck.

◆ Firmly tighten the chuck by turning sleeve (14) with one

hand while holding the tool with the other.

This tool is supplied with a double-ended screwdriver bit in

the bit holder (6).

◆ To remove the screwdriver bit from the bit holder, lift the

bit from the recess.

◆ To store the screwdriver bit, firmly push it into the holder.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (fig. A)

The battery needs to be charged before first use and

whenever it fails to produce sufficient power on jobs that

were easily done before. When charging the battery for the

first time, or after prolonged storage, it will only accept an

80% charge. After several charge and discharge cycles, the

battery will attain full capacity. The battery may become warm

while charging; this is normal and does not indicate a

problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

◆ To charge the battery (7), remove it from the tool and

insert it into the charger (9). The battery will only fit into

the charger in one way. Do not force. Be sure that the

battery is fully seated in the charger.

◆ Plug in the charger.

◆ Check if the red charging indicator (10) lights up. If the

green end of charge indicator (11) lights up now instead,

the battery is too hot and cannot be charged. If this

happens, remove the battery from the charger, let the

battery cool down for approx. 1 hour and re-insert it.

After approx. 30 minutes of charging, the red charging

indicator (10) will stop lighting and the green end of charge

indicator (11) will light up. The battery is now fully charged.

◆ Remove the battery from the charger.

Selecting the direction of rotation (fig. E)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

◆ To select forward rotation, push the forward/reverse

slider (2) to the left.

◆ To select reverse rotation, push the forward/reverse slider

to the right.

◆ To lock the tool, set the forward/reverse slider into the

centre position.

Selecting the operating mode or torque (fig. F)

This tool is fitted with a collar to select the operating mode

and to set the torque for tightening screws. Large screws and

hard workpiece materials require a higher torque setting than

small screws and soft workpiece materials. The collar has a

wide range of settings to suit your application.

◆ For drilling in wood, metal and plastics, set the collar (4)

to the drilling position by aligning the symbol

with the

marking (16).

◆ For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed as

follows:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker xtc 143 bk in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker xtc 143 bk Manual

Product: