578035

Black Decker XTA900EK T1 Manual

9
Zoom out
Zoom in
Previous page
1/92
Next page
9
ENGLISH
Removing
To remove the dust cassette (13), pull the item (13) to the
rear and off the outlet.
Fitting and removing the deflector (fig. D and E)
Warning! The deflector must be used when sanding metal
workpieces.
Fitting
Fit the deflector (14) over the dust extraction outlet.
Slide the deflector (14) on to the tool and make sure that it
is securely located.
Removing
To remove the deflector (14), pull the deflector to the rear
and off the outlet.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Use
Warning! Let the tool work at its own pace. Do not overload.
Variable speed control (fig. G)
The variable speed control (1) allows you to adapt the speed
of the tool to the workpiece material.
Use a low speed setting when using a fine grit, when working
with plastics or ceramics and when removing painted or
varnished surfaces.
Use a high speed setting when using a coarse grit and when
removing a lot of material.
Set the variable speed control knob (1) to the required
setting.
Switching on and off (fig. G)
To switch the tool on, press the on/off switch (2).
To switch the tool off, release the on/off switch (2).
For continuous operation:
- Press the on/off switch (2).
- Press the lock-on button (3).
- Release the on/off switch (2).
To switch the tool off when in continuous operation, press
and release on/off switch (2).
Emptying the dust cassette (fig. F)
The dust cassette (13) should be emptied every 10
minutes.
Pull the dust cassette (13) to the rear and off the tool.
Remove the cover (18) by twisting it counter-clockwise.
Hold dust cassette (13) with the filter (17) facing down and
shake the cassette (13) to empty the contents.
Shake the cover (18) to empty the contents.
Refit the cover (18) onto the dust cassette (13), twisting it
clockwise until it locks into place.
Refit the dust cassette (13) onto the tool.
Cleaning the dust cassette filter (fig. F)
Warning! Do not brush or use compressed air or sharp objects
to clean the filter. Do not wash the filter.
The dust cassette filter (17) is re-usable & should be
cleaned regularly.
Empty the dust cassette (13) as described above.
Pull the filter (17) off the dust cassette (13).
Shake off the excess dust by tapping the filter (17) into a
dustbin.
Replace the filter (17).
Fit the cover (18).
Slide the dust cassette (13) on to the tool and make sure
that it is securely located.
Special applications (fig. H, I and J)
Cranked arm (fig. H)
Use section A for grooving or sanding in the centre of
workpieces and in confined areas. Use section B for curved
surfaces.
Straight arm (fig. I)
Use the normal or narrow arms for general use, for slotting
and for making joints.
Narrow arm (fig. J)
Use the narrow arm for finer detail, for cutting and for
carving.
Hints for optimum use
Always hold the tool with both hands.
Do not exert too much pressure on the tool.
Regularly check the condition of the sanding belt (12).
Replace when necessary.
Always sand with the grain of the wood.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker XTA900EK T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker XTA900EK T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 3,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker XTA900EK T1

Black Decker XTA900EK T1 Quick start guide - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info