Manual Black Decker vpx 1201 (page 6 of 88) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

388385

Zoom out

Zoom in

1/88

ENGLISH

change to flashing (charging) state, as the charger

occasionally “tops off“ the battery charge.

X The charging indicator (10) will be lit as long as the

battery pack is connected to the plugged-in charger.

X Charge discharged batteries within 1 week. Battery life

will be greatly diminished if stored in a discharged state.

Charge indicators

If the charger detects a problem with a battery pack, the

charge indicator (10) will flash at a fast rate.

X If this occurs, re-insert the battery pack (8).

X If the problem persists, put a different battery pack in the

charger to determine if the charger is OK.

X If the new battery pack charges correctly, then the

original battery pack is defective and should be returned

to a service centre for recycling.

X If the new battery pack gives the same indication as the

original, take the charger to be tested at an authorized

service centre.

Note: It may take as long as fifteen minutes to determine that

the pack is defective.

If the battery pack is too hot or too cold, the LED will

alternately blink fast and slow, one flash at each speed and

repeat.

Battery chargers - daisy chaining (fig. C)

Single and dual port chargers can be electrically connected

in any order up to a maximum of 4 chargers. Each charger

has a power-in cord (11) which plugs into the electrical outlet

and a power-out cord (12) which plugs into the next charger.

To connect the chargers in a daisy chain:

X Plug the power-in cord (11) into an electrical outlet.

X Remove the power-in cord from the next charger and

plug in the power-out cord (12) from the charger that is

now plugged into the outlet.

X Repeat this process for the remaining chargers.

Chargers that are daisy chained together operate

independently as though each one was plugged into a

separate outlet, therefore a battery can be removed from

anywhere along the daisy chain without affecting the other

chargers.

Use

Switching on and off (fig. D)

X To switch the tool on, press the on/off trigger switch (7).

X To switch the tool off, release the on/off trigger

switch (7).

X A forward/reverse control button (4) determines the

direction of the tool and also serves as a lock off button.

X To select forward rotation, release the on/off trigger

switch (7) and move the forward/reverse control button

(4) to the left.

X To select reverse direction, move the forward/reverse

control button (4) in the opposite direction.

X The centre position of the control button (4) locks the

tool in the off position. Make sure that the on/off trigger

switch (7) is released before changing the position of

the forward/reverse control button (4).

Torque control (fig. D)

Your tool is fitted with an 8 position collar (2) to select the

operating mode and to set the torque for tightening screws.

Large screws and hard workpiece materials require a higher

torque setting than small screws and soft workpiece

materials.

X For drilling in wood, metal and plastics, set the collar (2)

to the drilling position symbol.

X For screwdriving, set the collar to the desired setting. If

you do not know the appropriate setting, proceed as

follows:

X Set the collar to the lowest torque setting.

X Tighten the first screw.

X If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

High/low speed selector (fig. D)

The 2-speed feature of your drill allows for greater versatility.

X To select the low speed, high torque setting (position 1),

turn the tool off and allow it to stop. Move the speed

selector button (3) to the right.

X To select the high speed, low torque setting (position 2),

turn the tool off and allow it to stop. Move the speed

selector button (3) to the left.

Warning! Do not move the speed selector button with the

tool switched on.

Keyless chuck (fig. E)

To insert a drill bit or other accessory:

X Hold the chuck (1) and rotate it in a counter clockwise

direction, as viewed from the chuck end.

X Insert the bit or other accessory fully into the chuck, and

tighten securely by rotating the chuck (1) in the

clockwise direction.

Warning! Do not attempt to tighten drill bits (or any other

accessory) by gripping the chuck and turning the tool on or

damage to the chuck and personal injury may occur.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker vpx 1201 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker vpx 1201 Manual

Product: