Manual Black Decker STC5433B (page 13 of 124) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709494

Zoom out

Zoom in

1/124

ENGLISH

(Original instructions)

u Press the release tabs (29) on the line spool cap (30),

as shown in gure R and remove the cap by pulling it

straight off.

u Pull the spool (31) out of the spool cap and clear any

broken line or cutting debris from the spool area.

u Before placing a new spool, "park" the cutting line (32)

in the holding slots (33).

u Feed the end of each line through the two holes (34) on

either side of the the spool cap ( 31 ) as shown in gure S

u Slide the spool back into the spool cap. Take care to

keep the line from becoming trapped under the spool.

u Pull slack line through until it pulls out of the holding

slots.

u Align the tabs on the spool cap with the slots in the

housing (gure R).

u Push the cap onto the housing until it snaps securely

into place.

Note: Make sure that cap is fully positioned, listen for two

audible clicks to ensure both lugs are correctly located.

Power the appliance on. In a few seconds or less you’ll hear

the nylon line being cut automatically to the proper length.

Caution: To avoid appliance damage, if the cutting line

protrudes beyond the trimming blade, cut it off so that it just

reaches the blade.

Note: Other replacement parts (guards, spool caps, etc.)

are available through BLACK+DECKER service centers. To

nd your local service location visit www.blackanddecker.com.

Warning! The use of any accessory not recommended

by BLACK+DECKER for use with this appliance could be

hazardous.

Note: The tool has two cutting systems:

u AFS: Single line autofeed for light trimming and edging.

u HDL: Heavy Duty Dual Line cutting system for more

overgrown areas.

Note: The HDL spool may be used in trimming mode only.

Fitting a new piece of heavy duty cutting line (g.

T & U)

Replacement packs of 10 heavy duty cutting lines are

available from your BLACK+DECKER dealer (cat. no. A6489).

To t a new piece of cutting line, proceed as follows:

u Unplug the tool.

u Keep the tabs (37) depressed and remove the HDL cap

(16) from the housing (12).

u Remove any dirt and grass from the HDL cap (16) and

housing.

u Remove the used piece of line from the HDL cap (16).

u Thread a new piece of line (35) through the eyelets (36) in

either side of the HDL cap.

u Put the central ferrule (39) in the indicated position (Fig.

U).

u Re-t the HDL cap.

Rewinding spool from bulk line (use only 20mm.

round diameter line)

Do not use square, star or other shaped line or larger

diameter. These may cause feeding issues or overload the

motor.

Bulk line is also available for purchase from your local retailer.

Note: Hand wound spools from bulk line are likely to

become tangled more frequently than BLACK+DECKER

factory wound spools. For best results, factory wound spools

are recommended.

To install bulk line, follow the steps below:

u Remove battery from appliance.

u Remove the empty spool from the appliance as

described in “Replacing the spool.”

u Remove any remaining cutting line from the spool.

u First, wind new line in the channel of the spool closest

to the holding slots as shown in Figure V.

u Place the end of the cutting line (32) into the retaining

hole (40) (Figure W).

u Wind the cutting line onto the spool in the direction

of the arrow on the bottom of the spool. Make sure to

wind the line on neatly and in layers. Do not crisscross.

u When the wound cutting line reaches the beginning of the

holding slots, cut the line approximately 106 mm.

u Push the line in the holding slot on one side of the spool

to hold the rst line while you wind the second line.

u Repeat the above procedure for the second cutting line

on the lower section of the spool.

u Fit the spool into the appliance as described in

“Replacing the spool".

Maintenance

Your BLACK+DECKER corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool/appliance care and regular

cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker STC5433B in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker STC5433B Manual

Product: