Manual Black Decker STC1820D (page 9 of 112) (All languages)

606056

Zoom out

Zoom in

1/112

ENGLISH

(Original instructions)

Adjusting the position of the secondary handle (g.

The second handle (5) can be adjusted to provide optimum

balance and comfort.

u Press in the button (15) on the left side of the handle.

u Rotate the second handle (5) into the required position.

u Release the button (15).

Warning! Ensure that the teeth on the button are correctly

aligned in slots in the handle and that the handle is secure.

Adjusting the height of the tool (g. E)

This tool has a telescopic mechanism, allowing you to set it to

a comfortable height. There are multiple height settings.

To adjust the height setting, proceed as follows:

u Loosen the adjustment collar (16) by turning it clockwise.

u Gently pull the tube (17) in or out of the handle (2) to the

desired height.

u Tighten the adjustment collar (16) by turning anti-clock-

wise.

Releasing the cutting line

In transit, the cutting line is taped to the spool housing.

Warning! Before assembly, remove the battery from the tool.

u Remove the tape holding the cutting line to the spool

housing (7).

Fitting and removing the battery (g. F)

u To t the battery (4), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button (18) while

at the same time pulling the battery out of the receptacle.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. G)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (4), insert it into the charger (19).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (20) will ash green continuously

(slowly).

The charge is complete when the charging indicator (20)

lights green continuously. The charger and the battery can be

left connected indenitely with the LED illuminated. The LED

will change to ashing green (charging) state as the charger

occasionally tops up the battery charge. The charging indica-

tor (20) will be lit as long as the battery is connected to the

plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the charg-

ing indicator (20) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (4).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 30 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Setting the tool to trimming or edging mode (g. H,

I, J & K)

The tool can be used in trimming mode as shown in g. H or

in edging mode to trim overhanging grass along lawn edges

and ower beds as shown in g. I.

Trimming mode (g. E, H & J)

For trimming, the trimmer head should be in the position

shown in g. J. If it is not:

u Remove the battery from the tool.

u Loosen the adjustment collar (16) by turning it clockwise.

u Whilst holding the handle (2), rotate the head (8) clock-

wise.

u Tighten the collar (16) by turning it anti-clockwise.

Note: Note: The head will only rotate in one direction.

Edging mode (g. E, I & K)

For edging, the trimmer head should be in the position shown

in g. K. If it is not:

u Remove the battery from the tool.

u Loosen the adjustment collar (16) by turning it clockwise.

u Whilst holding the handle (2), rotate the head (8) anti-

clockwise.

u Tighten the collar (16) by turning it anti-clockwise.

Note: The head will only rotate in one direction.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker STC1820D in the language / languages: All languages as an attachment in your email.

The manual is 6,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker STC1820D Manual

Product: