606052

Black Decker ST5530 Manual

9
Zoom out
Zoom in
Previous page
1/100
Next page
9
ENGLISH
(Original instructions)
u Disconnect the tool from the supply.
u Loosen the adjustment collar (15) by turning it clockwise.
u Whilst holding the handle (2), rotate the head (8) anti-
clockwise.
u Tighten the collar (15) by turning it anti-clockwise.
Note: The head will only rotate in one direction.
Switching on and off
u To switch the tool on, squeeze the trigger lever (1).
u To switch the tool off, release the trigger lever.
Warning! Never attempt to lock the trigger lever in the on
position.
Hints for optimum use
General
u In order to achieve optimum cutting results, only cut dry
grass.
Trimming
u Hold the tool as shown in g. I.
u Gently swing the trimmer from side to side.
u When cutting long grass, work in stages from the top. Take
small cuts.
u Keep the tool away from hard objects and delicate plants.
u Cutting line will wear faster and require more feeding if
the cutting is done along pavements or other abrasive
surfaces or heavier weeds are being cut.
u If the tool starts running slowly, reduce the load.
Edging
Optimum cutting results are achieved on edges deeper than
50 mm.
u Do not use the tool to create edges. To create edges,
use an edging spade.
u Guide the tool on its wheel (9) or edge guide (10) as
shown in g. J.
u To make a closer cut, slightly tilt the tool.
Fitting a new spool of cutting line (g. K)
Replacement spools of cutting line are available from your
Black & Decker dealer (cat. no. A6481).
u Unplug the tool.
u Keep the tabs (17) depressed and remove the spool cover
(18) from the spool housing (7).
u Remove the empty spool (19) from the spool housing.
u Remove any dirt and grass from the spool cover and
housing.
u Take the new spool and push it onto the boss in the spool
housing. Rotate the spool slightly until it is seated.
u Unclip the end of the cutting line and guide the line into
the eyelet (20). The line should protrude approx. 11 cm
from the spool housing.
u Align the tabs (17) on the spool cover with the cut outs
(21) in the spool housing.
u Push the cover onto the spool housing until it snaps
securely into place.
Warning! If the cutting lines protrude beyond the trimming
blade (22), cut them off so that they just reach the blade.
Winding new line onto an empty spool (g. L, M &
N)
You may wind new cutting line onto an empty spool.
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6170 (25 m), A6171 (40 m)).
u Remove the empty spool from the tool as described
above.
u Remove any remaining cutting line from the spool.
u Feed 2 cm of cutting line into the hole (23) in the spool as
shown (g. L).
u Bend the cutting line and anchor it in the L-shaped slot
(24).
u Wind the cutting line onto the spool in the direction of the
arrow. Make sure to wind the line on neatly and in layers.
Do not criss-cross (g. N).
u When the wound cutting line reaches the recesses (25),
cut the line. Let the line protrude approx. 11 cm from the
spool and hold a nger on the line to keep it in place (g.
M).
u Proceed as described above to t the spool on the tool.
Warning! Only use the appropriate type of Black & Decker
cutting line.
Troubleshooting
If your tool seems not to operate properly, follow the instruc-
tions below. If this does not solve the problem, please contact
your local Black & Decker repair agent.
Warning! Before proceeding, unplug the tool.
Appliance runs slowly
u Check that the spool housing can rotate freely. Carefully
clean it if necessary.
u Check that the cutting line does not protrude more than
11 cm from the spool housing. If it does, cut it off so that it
just reaches the line trimming blade.
Automatic line feed does not work
u Keep the tabs depressed and remove the spool cover
from the housing.
u Pull the cutting line until it protrudes 11 cm from the hous-
ing. If insufcient cutting line is left on the spool, install a
new spool of cutting line as instructed above.
u Align the tabs on the spool cover with the cut outs in the
housing.
u Push the cover onto the housing until it snaps securely
into place.
u If the cutting line protrudes beyond the trimming blade, cut
it off so that it just reaches the blade.
If the automatic line feed still does not work or the
spool is jammed, try the following suggestions:
u Carefully clean the spool cover and housing.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ST5530 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ST5530 in the language / languages: All languages as an attachment in your email.

The manual is 5,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info