Manual Black Decker SMS216 T1 (page 11 of 140) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

578653

Zoom out

Zoom in

1/140

ENGLISH

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Note: This tool is accurately adjusted before shipping from

the factory. Check the following accuracy and readjust them

if necessary in order to obtain the best results in operation.

Laser beam

The laser beam alignment is set at manufacturing source

and is not user adjustable.

Mitre angle adjustment (fig. B)

The sliding compound mitre saw scale can be easily read

showing mitre angles from 0° to 45° to the left and the right.

The most common angle cut setting slots have positive

stops, permitting fast adjustments to the required position.

Follow the process below for the quickest and most accurate

adjustments.

Mitre lock knob (fig. B)

The mitre lock knob (7) allows the saw to be set to specific

angles other than the preset angles of 0°, 15°, 22.5°, 31.6°,

and 45°, which are set using the mitre detent lever (8).

Adjusting the bevel stops at 90° and 45° (fig. C - E)

X Loosen the bevel lock handle (22) and move the cutting

head all the way to the right and tighten the bevel lock

handle.

X Use a square to set the blade at 90° to the table (fig. D).

X If an adjustment is necessary, loosen the lock nut (29)

and adjust the bolt (28) with the wrench so that the blade

is 90° to the table.

X Tighten the lock nut (29).

X Align the bevel indicator (21) with the 0° mark by

adjusting the screw (27).

When adjusting the 45° stop, make sure that the left-hand

high sliding fence (42) is adjusted so that the cutting head

can be moved to the 45° position (fig.P).

X Release the high sliding fence clamp (43) and move the

high fence (42) away from the blade.

X Tighten the high sliding fence clamp (43).

X Follow the same procedures for the 90° but move the

cutting head to the left and use the lock nut (31) and

adjustment bolt (30).

Adjusting the fence (fig. F - G)

X Lower the cutting head and push in the carriage lock pin

(34). Make sure that the table is in 0° mitre position.

X Place a combination square against the fence (12) and

next to the saw blade (24) (fig. F).

X If the blade does not contact the square along it’s length,

loosen the two screws (33) (fig. G) and adjust the fence.

X Tighten the two screws (33).

Bench mounting (fig. H)

Note: We highly recommend that you bolt this mitre saw

securely to a work bench to gain the maximum stability of

your machine. Make sure that the machine is fixed to a

bench whenever possible.

X Locate and mark the four bolt holes on the bench.

X Drill the bench with an Ø10 mm drill bit.

X Bolt the mitre saw onto the bench with bolts, washers

and nuts.

Note: These fasteners are not supplied with the tool.

Use

X Place your hands no closer that 150 mm from the blade.

X Hold the workpiece tightly to the table and the fence

when cutting. Keep your hands in position until the

switch has been released and the blade has completely

stopped.

X Always make dry runs (without power) before finish cuts

so that you can check the path of the blade.

X Do not cross your hands.

X Keep both feet firmly on the floor and maintain proper

balance.

X As you move the saw arm left and right, follow it and

stand slightly to the side of the saw blade.

X Sight through the guard louvres when following a pencil

line.

Basic pullover mitre saw operations

X Always use the work piece clamp (44) to hold the work

piece firmly. Two holes (32) are provided for the clamp

(fig. G).

Warning! Make sure that the workpiece is securely held in

place with the clamp before operation. Severe personal

injury can occur if the workpiece is not secured.

X Always position the work piece against the fence. Any

piece that is bowed or warped and cannot be held flat on

the table or against fence may trap the blade and should

not be used.

Pullover cut (fig. I & J)

Warning! Never pull the cutting head assembly and rotating

blade toward you during the cut. The blade may try to climb

up on the top of the workpiece, causing the cutting head

assembly and spinning blade to kick back. Never lower the

rotating saw blade down before pulling the cutting head to

the front of the saw.

X Unlock the carriage (16) with the lock knob (14) and

allow the cutting head assembly to move freely.

X Move the cutting head to the required mitre angle and

bevel angle in accordance with the mitre cut and bevel

cut procedures.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker SMS216 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker SMS216 T1

Black Decker SMS216 T1 Quick start guide - English - 20 pages

Black Decker SMS216 T1 User Manual - Turkish - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker SMS216 T1 Manual

Product: