25090
5
Zoom out
Zoom in
Previous page
1/68
Next page
5
ENGLISH
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing accessories (fig. A)
Make sure that the tool is switched off and unplugged.
Activate the spindle lock (2) by setting it to position B as
shown.
Slacken the collet nut (5) by turning counterclockwise.
Insert the shaft of the accessory into the collet as far as it
will go.
Securely tighten the collet nut.
Release the spindle lock (2) by setting it to position A as
shown.
Warning!
Make sure that the collet size matches the shaft diameter.
Never tighten the collet nut without an accessory in the
collet.
Tighten and loosen the collet by hand if possible.
If necessary, use the supplied wrench to loosen the collet.
Do not use any tools that could mark the finish or break
the collet.
Replacing collets (fig. B)
This tool is supplied with a 3.2 mm collet. Different sizes are
available as an accessory to accomodate a wide range of
accessories. To fit the correct collet for the accessory to be
used:
Make sure that the tool is switched off and unplugged.
Activate the spindle lock (2) by setting it to position B as
shown.
Remove the collet nut (5) by turning counterclockwise.
Pull the collet off the spindle (6).
Place the new collet into the spindle.
Loosely screw the collet nut onto the spindle.
Release the spindle lock (2) by setting it to position A as
shown.
Use
Warning!
Let the tool work at its own pace. Do not overload.
If you are not sure about the correct speed setting, start
with a low speed setting and gradually increase it until you
find the optimum setting.
Where indicated, never exceed the speed rating of an
accessory. The wire brush accessory must not be used
above speed setting 3 (15,000 min
-1
).
Variable speed control (fig. C)
The variable speed control allows you to adapt the speed of
the tool to the application.
Set the control knob (3) to the desired setting. At setting 1
the tool will operate at low speed, 8,000 min
-1
. At setting 6
the tool will operate at the maximum speed, 27,000 min
-1
.
The table below suggests settings for different applications.
Application Setting
Drilling holes 4-5
Cutting metal 5-6
Engraving metal 4-5
Removing rust 1-2
Sharpening 3-5
Polishing 1-2
Sanding wood 5-6
Removing paint 3-5
Switching on and off (fig. D)
To switch the tool on, slide the on/off switch (1) forward
(position I).
To switch the tool off, slide the on/off switch to the rear
(position O).
Hints for optimum use (fig. E)
Always hold the tool securely. For precision work, hold the
tool near the front.
Do not exert too much pressure on the tool.
Consult your retailer for more information on available
accessories.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker RT650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker RT650 in the language / languages: Dutch as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker RT650

Black Decker RT650 User Manual - English - 16 pages

Black Decker RT650 User Manual - French, Italian, Portuguese, Spanish, Norwegian - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info