Manual Black Decker PS7525 (page 9 of 100) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709524

Zoom out

Zoom in

1/100

ENGLISH

(Original instructions)

u Once chain tension is correct, tighten the locking nut (8) in

the sprocket cover (7).

u Ret the Locking Nut cap (13).

Note: When the chain is new, check the tension frequently

(after disconnecting from the mains) during the rst 2 hours of

use because a new chain stretches slightly.

Extending the pole pruner (g. F)

u Open pole extension release lever (6) (g.F)

u Hold the extension pole with one hand, slide the saw head

away from the release lever.

u When at desired extension, close the release lever.

Warning! Periodically check the connections to ensure that

they are tightened securely.

Adjusting the head angle (g. G)

u Loosen Knob (5), support pole with one hand and rotate

head with other.

u Once in desired position support head and pole whilst

tightening knob (5).

Use

Warning! Let the tool work at its own pace. Do not overload.

Switching on and off (g. H)

For your safety, this tool is equipped with a double switching

system. This system prevents starting the tool inadvertently.

Switching on

u Push the lock-off button (2) using your thumb and at the

same time squeeze the on/off switch with your ngers (1).

u Once the tool is running you can release the lock-off but-

ton (2).

Switching off

u Release the on/off switch (1).

Warning! Never attempt to lock a switch in the on position.

Pruning (g. I)

Before attempting to prune a tree, ensure there are no by-laws

or regulations that would prohibit or control the felling of the

tree.

u Be aware of the direction a branch may fall. Consider all

conditions that may affect the direction of fall, including:

u the length and weight of the branch to be cut

u the intended direction of fall

u any unusual heavy limb structure or decay

u the presence of surrounding trees and obstacles,

including overhead lines, the intertwinement with other

branches and the speed and direction of the wind.

Tree branches are liable to swing towards the tree trunk. In

addition to the user, any bystander, building or object below

the branch is at risk of being struck by the branch.

u Consider access to the tree limb.

u Make sure the tool is running at full speed before making

a cut.

u Hold the tool firmly in place to avoid possible bouncing or

sideways movement of the tool.

u Guide the tool through the branch using light pressure.

When cutting heavy branches, where a partial cut may

splinter and damage the tree, proceed as follows:

u Make the first cut 15 cm from the tree trunk on the

underside of the limb. Use the top of the guide bar (9)

to make this cut.

u Cut one third through the diameter of the limb. Then cut

down from the top.

Cleaning, maintenance and storage

Your BLACK+DECKER corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

Regularly clean the motor housing using a damp cloth. Do not

use any abrasive or solvent-based cleaner.

After use and before storage

u Regularly clean the ventilation slots with a clean, dry paint

brush.

u To clean the appliance/tool/charger, use only mild soap

and a damp cloth. Never let any liquid get inside and

never immerse any part into liquid.

u Remove debris using a hard brush.

u Lubricate the chain with oil.

Checking and adjusting the chain tension (fig. E)

u Check the saw chain tension. The tension is correct when

the saw chain (10) snaps back after being pulled away 3

mm from the saw chain bar with light force from the middle

nger and thumb. There should be no ‘sag’ between the

guide bar (9) and the saw chain (10) on the underside.

To adjust the tension:

u Loosen the Locking nut (8).

u Turn the screw (16) clockwise.

Warning! Do not over-tension the chain as this will lead to

excessive wear and will reduce the life of the bar and chain.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker PS7525 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker PS7525 Manual

Product: