473014

Black Decker PS142 Manual

7
Zoom out
Zoom in
Previous page
1/94
Next page
7
ENGLISH
Using the 3 hour charger
To charge the battery (5), remove it from the tool and slide
the charger receptacle (9) onto the battery.
Plug in the charger (8).
The battery will become warm while charging. After approx.
3 hours of charging, the battery will be sufficiently charged for
use in regular applications. After approx. 6 hours of charging,
the battery will be fully charged.
Remove the charger receptacle from the battery.
Warning! Do not replace the charger unit with a regular mains
plug.
Using the 1 hour charger
To charge the battery (5), remove it from the tool and
insert it into the charger (8). The battery will only fit into
the charger in one way. Do not force. Be sure that the
battery is fully seated in the charger.
Plug in the charger.
Check if the charging indicator (10) is red. If the charging
indicator lights up is green, the battery is either fully
charged or too hot and cannot be charged. If this happens,
remove the battery from the charger, let the battery cool
down for approx. 1 hour and re-insert it.
After approx. 1 hour of charging, the charging indicator (10)
will change colour from red to green. The battery is now fully
charged.
Remove the battery from the charger.
Checking the battery condition (fig. E)
This tool is fitted with a battery charge indicator, which allows
you to check the condition of the battery.
Press and hold down the button (15).
Check to see how many of the lights (6) are on:
Battery charge
1 light low
2 lights medium
3 lights high
Selecting the direction of rotation (fig. F)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
(2) to the left.
To select reverse rotation, push the forward/reverse slider
to the right.
To lock the tool, set the forward/reverse slider into the
centre position.
Selecting the torque (fig. G)
This tool is fitted with a unique collar to set the torque for
various screwdriving and drilling applications. Large screws
and hard workpiece materials require a higher torque setting
than small screws and soft workpiece materials. The collar
has a wide range of settings represented by symbols to suit
your application. For the definition of the symbol refer to the
listing below.
For drilling in wood, metal and plastics, set the collar (3) to
the symbol corresponding to the appropriate drilling
application by aligning the symbol with the marking (16).
For screwdriving, set the collar to the desired setting. If
you do not yet know the appropriate setting, proceed as
follows:
- Set the collar (3) to the lowest torque setting.
- Tighten the first screw.
- If the clutch ratchets before the desired result is
achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
setting. Use this setting for the remaining screws.
Torque/speed range
Non-working position used only to switch between
low speed, high speed and high torque.
Screwdriving applications
Torque range: low torque for
small screws and high torque
for large screws
High toque drilling applications
Large drill bits in steel
Large spade bits in wood
High speed drilling applications
Small diameter drill bits in wood, plastic and metal
Large diameter drill bits in wood, plastic, metal
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker PS142 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker PS142 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info