578616
6
Zoom out
Zoom in
Previous page
1/72
Next page
6
ENGLISH
Fitting sanding sheets (fig. D)
Detach the two diamond-shaped tips (23) from the
sanding sheet (19).
Hold the tool with the sanding base facing upwards.
Place the sanding sheet (19) onto the sanding base,
making sure that the holes in the sheet line up with the
holes in the base.
The diamond-shaped tip (23) can be reversed and replaced
when worn.
When the front part of the tip is worn, detach it from the
sheet, reverse it and press it onto the sanding base again.
When the whole tip is worn, remove it from the sanding
base and fit a new tip.
Warning! Never use the sanding head without a sanding
sheet or accessory in place.
Tip of the sanding base (fig. E)
When the sanding base tip (8) is worn, it can be reversed or
replaced. Spare parts are available from your Black & Decker
dealer.
Reverse or replace the worn part.
Fitting and removing the scraper head (fig. F)
Slide the scraper head (13) onto the shaft (10).
Align the tab on the clamp plate (11) with the slot in the
shaft.
Fit the clamp plate to the shaft by tightening the screw (24).
To remove the head, remove the screw (19) and the clamp
plate, and pull the head from the shaft.
Removing and fitting the blade cover (fig. G)
Hold the blade cover (14) at the ends.
Lift the blade cover slightly to release it from the screw
(25) and pull the cover off. Take care not to contact the
edges of the blade (26).
To fit the blade cover, hold the cover at the ends and
place it over the claw blade. Push the cover until it snaps
into place.
Warning! Always keep the blade cover in place when the
scraper head is not being used.
Fitting and removing a parallel blade (fig. H)
Select the required parallel blade.
Align the slot on the mounting end of the blade with the
slot in the shaft (10).
Align the tab on the clamp plate (11) with the slot in the
shaft (10) and the blade.
Fit the clamp plate to the shaft by tightening the screw (27).
To remove the blade, remove the screw (19) and the
clamp plate, and take the blade from the shaft.
Replacing the cutting blade (fig. I)
The cutting blade provided with this tool is reversible.
Replacement cutting blades can be obtained from your local
retailer.
Loosen the screw (28) and remove it.
Remove the cutter clamp plate (29).
Reverse the blade (26) so that the unused side comes in
position. If both sides are worn, the blade must be replaced.
Re-install the cutter clamp plate.
Re-fit the screw and tighten it.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Do not cover the ventilation slots when using the
tool to avoid overheating.
Selecting the direction of rotation (fig. J)
For tightening screws, use forward (clockwise) rotation.
For loosening screws, use reverse (counterclockwise) rotation.
To select forward rotation, press the lock-off button (30)
and push the forward/reverse switch (5) to the left.
To select reverse rotation, press the lock-off button and
push the forward/reverse switch to the right.
Warning! Never change the direction of rotation while the
motor is running.
Switching on and off
To switch the tool on, press the on/off switch (1).
For continuous operation, press the lock-on button (2) and
release the on/off switch.
To switch the tool off, release the on/off switch.
To switch the tool off when in continuous operation,
press the on/off switch once more and release it.
Hints for optimum use
Screwdriving
Always use the correct type and size of screwdriver bit.
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
Always hold the tool and screwdriver bit in a straight line
with the screw.
Sanding
Do not exert too much pressure on the tool.
Regularly check the condition of the sanding sheet.
Replace when necessary.
When sanding new layers of paint before applying
another layer, use extra fine grit.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker MT3000K T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker MT3000K T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker MT3000K T1

Black Decker MT3000K T1 Quick start guide - English - 12 pages

Black Decker MT3000K T1 User Manual - Polish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info