Manual Black Decker MFL143 (page 8 of 124) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

529645

Zoom out

Zoom in

1/124

ENGLISH

(Original instructions)

Fitting and removing a drill bit or screwdriver bit

The drill/screwdriver head is tted with a keyless chuck to

allow for an easy exchange of bits.

u Lock the tool by setting the forward/reverse slider (2) to

the centre position.

u Open the chuck (9) by turning the front part clockwise with

one hand while holding the rear part with the other.

u Insert the bit shaft into the chuck (9).

u Firmly tighten the chuck (9) by turning the front part anti-

clockwise with one hand while holding the rear part with

the other.

u To remove the screwdriver bit from the bit holder, lift the bit

from the recess.

u To store the screwdriver bit, rmly push it into the holder.

Fitting and removing a saw blade (g. D)

u Lock the tool by setting the forward/reverse slider (2) to

the centre position.

u To t a saw blade, press the lever (15) down and hold it in

this position.

u Insert the saw blade into the blade clamp (11) as shown.

Make sure that the teeth are pointing to the front.

u Release the lever.

u To remove the saw blade, press the lever (15) down and

pull the saw blade from the holder.

Fitting and removing sanding sheets (g. E)

The sanding head uses pre-cut sanding sheets.

u Lock the tool by setting the forward/reverse slider (2) to

the centre position.

u Before tting a new sheet, remove the two additional

diamond tips (16).

u To t a sanding sheet, line it up with the sanding base (14)

as shown.

u Press the sheet rmly and evenly onto the sanding base,

making sure that the holes in the sheet coincide with the

holes in the base.

u To remove the sheet, pull it off the sanding pad.

Warning! Never use the sanding head without a sanding

sheet or accessory in place.

Replacing the diamond sanding tip (g. F)

Sanding sheets are supplied with two replacement diamond

tips. The diamond tip can be reversed when worn. When both

sides are worn, replace the diamond tip.

u Lock the tool by setting the forward/reverse slider (2) to

the centre position.

u To reverse the tip, remove it, turn it 180° and press it back

onto the base.

u To replace the tip, pull the old tip off the base and press a

new one onto the base.

Warning! When removing the tip from the pad, be careful not

to pull the pad off the sanding base.

Fitting and removing the dust extraction adaptor

(g. G)

u Line up the dust extraction adaptor (17) with the sanding

head (13) as shown.

u Press the adaptor rmly and evenly in to the sanding

base.

u Connect a vacuum cleaner to the dust extraction adaptor.

u To remove, pull the dust extraction adaptor (17) out of the

sanding head (13).

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, oors or ceilings, check for

the location of wiring and pipes.

Charging the battery (g. H)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 0 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (5), insert it into the charger (18).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (19) will ash green continuously

(slowly).

The charge is complete when the charging indicator (19)

lights green continuously. The charger and the battery can be

left connected indenitely with the LED illuminated. The LED

will change to ashing green (charging) state as the charger

occasionally tops off the battery charge. The charging indica-

tor (19) will be lit as long as the battery is connected to the

plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker MFL143 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker MFL143 Manual

Product: