Manual Black Decker LZR210 T1 (page 5 of 56) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

578015

Zoom out

Zoom in

1/56

ENGLISH

- Very humid conditions

- Shielded cables

◆ Before use, always test the tool by detecting a known

pipe or wire.

◆ If in doubt contact a qualified contractor.

Warning! This tool will not detect wires in circuits isolated

from the mains supply, cables operating at direct current (DC)

or wires used for telecommunication or computer systems.

Hidden wires (e.g. wall lights) may not be detected when

switches are in the off position.

Warning! This tool will not detect pipes of any other material

than metal.

Features

1. On/off switch (laser)

2. On/off switch (stud/metal finder)

3. Mode selector switch

4. LED indicators (stud/metal finder)

5. LED indicator (wire detector)

6. Insert holder

7. Marking/hanging insert

8. Keyhole insert

9. Spacer insert

10. Drywall pin

11. Laser apertures

Assembly

Fitting the battery (fig. A)

◆ Depress the release button and remove the battery cover

(12) from the tool.

◆ Connect the battery to the connector. The larger battery

terminal connects to the smaller connector terminal.

◆ Refit the cover and let it click into place.

Fitting and removing inserts

The marking/hanging insert (7) is used to make a mark on the

level line or to hang the tool on a drywall board using the

drywall pin (10) supplied. The keyhole insert (8) is used to

hang the tool on other types of wall using a screw or nail.

The spacer insert (9) is used to extend the laser line.

Fitting

◆ Place the insert into the holder from the back of the tool.

◆ Align the notches on the insert with the recesses in the

insert holder (6).

◆ Let the insert click into place.

Removing

◆ Keep the notches on the insert depressed.

◆ Push the insert out of the holder.

Use

Using the laser level function (fig. B)

◆ Place the tool flat against the wall as shown.

◆ Push the on/off switch (1) up to switch the tool on.

◆ Move the tool as necessary to position the laser lines.

◆ If necessary, hang the unit on the wall using the

appropriate insert.

Note: the laser lines will only be level if the tool is kept within

5° from vertical.

◆ Push the on/off switch (1) down to switch the tool off.

Using the spacer insert (fig. C)

If you need to extend the laser line, use the spacer insert (9)

as shown.

Note: the stud sensor cannot be used with the spacer insert

fitted.

Enhancing the visibility of the beam (fig. D)

If because of the lighting conditions it is difficult to see the

laser line, you can use one of the inserts as shown to enhance

the line.

Selecting the operating mode

◆ Set the mode selector switch (3) to the ‘STUD’ position for

the detection of wooden studs.

◆ Set the mode selector switch (3) to the ‘METAL’ position

for the detection of metal studs, pipes, etc.

Using the stud finder function (fig. E)

You can use this function to find wooden and metal studs

through drywall boards up to 18 mm thick.

◆ Fit the marking insert (7).

◆ Set the mode selector switch (3) to the required position.

◆ Place the tool flat against the wall as shown.

◆ Keep the on/off switch (2) depressed.

The red LED indicator (4) will light up and the buzzer will

sound once while the tool is calibrating. After calibration is

completed:

◆ Slowly slide the tool in a horizontal direction. Make sure

not to tilt or lift the tool.

◆ When the red LED indicator (4) lights up, slow down and

slide the tool further until the buzzer sounds and the top

green LED indicator is on.

This position indicates the one edge of the stud.

◆ Mark this position through the hole in the marking insert

(7).

◆ Move the unit further until the LED indicators are off.

◆ While still keeping the on/off switch (2) depressed, move

the tool in the opposite direction.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker LZR210 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker LZR210 T1

Black Decker LZR210 T1 User Manual - Polish - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker LZR210 T1 Manual

Product: