577931

Black Decker KX2001K T1 Manual

7
Zoom out
Zoom in
Previous page
1/100
Next page
7
ENGLISH
(Original instructions)
u
Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
u
Impairment of hearing.
u
Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech
and MDF.)
Labels on tool
The following pictograms are
shown on the tool:
;
Warning!
To reduce the risk of
injury, the user must read the instruc-
tion manual.
Electrical safety
#
This tool is double insulated; there-
fore no earth wire is required. Always
check that the power supply cor-
responds to the voltage on the rating
plate.
u
If the supply cord is damaged, it must be
replaced by the manufacturer or an author-
ised Black & Decker Service Centre in order
to avoid a hazard.
Extension cables
u
A 2 or 3 core cable may be used as the
appliance is double insulated and of class II
construction.
u
Up to 30m (100 ft) can be used without loss
of power.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Heat control knob
3. Nozzle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting an accessory (g. C, D, E & F)
A selected range of accessories can be obtained from your
local retailer.
w Cone nozzle (5): Concentrates the air stream on a
smaller area.
w Fish tail (6): Spreads the air stream over a wider area
w Spoon reector (7): For soldering pipes.
w Glass protector (8): For the protection of glass during
paint stripping.
w Scraper (9): For the removal and stripping paint and
varnish.
u Fit the connecting piece of the accessory over the nozzle
(2).
Use
Setting the temperature (g. A)
u To increase the temperature setting, turn the heat control
knob (2) clockwise.
u To reduce the temperature setting, turn the heat control
knob anti-clockwise.
Switching on and off
u To switch the tool on at the low air speed, low heat, set the
on/off switch to position I.
u To switch the tool on at the high air speed, high heat, set
the on/off switch to position II.
u To switch the tool off, set the on/off switch to position O.
Using the tool
Your tool is tted with a thermostat for your safety. Using the
tool continuously for very long periods or other severe duty
cycles may cause the tool to overheat and the element to stop
working. It is therefore recommended that you allow the tool to
cool down at regular intervals during use.
u Allow the tool to heat up for a few seconds before use.
u At rst use some smoke may emit from the nozzle. This is
normal and will soon decrease.
u Use a low temperature setting for drying paint and varnish,
removing stickers, shrinking insulation tubes, and thawing
frozen pipes.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KX2001K T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KX2001K T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info