531202
26
Zoom out
Zoom in
Previous page
1/80
Next page
26
ENGLISH
placed on the
stands (4). Always
point your
heatgun away
from you. Secure
the cable to
prevent pulling
your heatgun off
the stand. Do not
touch the nozzle
and ensure that
nothing is
dropped into the
nozzle. Carefully switch off your heatgun and then
allow it to cool (see cooling down procedure).
FITTING THE SCRAPER (KX1682, KX1683)
Ensure your heatgun is cool.
Align the slot of
the scraper blade
with the
protrusion on the
blade holder and
position under the
retaining screw.
Note: Ensure the hole in the scraper is to the left of the
screw in the blade holder.
Tighten the
retaining screw.
Place the blade
holder over the
nozzle outlet.
Ensure it is
aligned. The small
bump on the
inside of the blade
holder engages with the recess on the nozzle. Tighten
the blade holder clamp screw.
PAINT STRIPPING
When stripping a
point next to
glass, it is
necessary to
protect the glass
from the heat.
A Black & Decker
glass protector
nozzle is used for
this purpose (available as an accessory). Your heatgun
is not suitable for stripping metal framed windows.
This is because the heat from the heatgun is
conducted through the metal and can crack the glass.
Scrape with the grain of the wood wherever possible.
Do not linger on one spot for too long as the surface
may char or ignite.
KX1682, KX1683 only:
Your heatgun is designed for use with the scraper
blade to strip paint.
Proceed as follows:
Ensure the nozzle
is cool and fit the
scraper blade.
Hold your heatgun
with the scraper
blade in contact
with the surface
at an angle of 30-40˚.
When the paint softens, scrape firmly. Experiment to
establish the length of time necessary to apply the heat
to obtain optimum results. Scrape the softened paint
immediately or it will harden again.
Take care to prevent paint and debris collecting on the
scraper because it may ignite. Carefully clean the
scraper blade with a knife should any build up occur.
When scraping vertical surfaces, scrape downwards
to prevent debris falling into the nozzle.
Note: When stripping a point next to glass, use a glass
protector nozzle instead of the scraper blade - a
manual scraper is needed to scrape off the paint.
CD700, KX1600 only:
Your heatgun is designed to soften paint and laquer
enabling it to be removed using a good quality
hand scraper.
Proceed as follows:
Direct the hot air onto the area to be removed. When
the paint softens, scrape firmly. Experiment to establish
the length of time necessary to apply the heat to obtain
optimum results. Scrape the softened paint
immediately or it will harden again.
OTHER USES FOR YOUR HEATGUN
On low heat (KX1682, KX1683):
Drying paint and varnish.
Removing stickers and decorations.
Waxing and dewaxing (eg. skis).
Drying wet timber prior to filling.
Shrinking PVC wrapping and insulation tubes.
Thawing frozen pipes.
1
2
30-40°
CD700 KX1600-1683 ML p22-39 07/01/2000, 3:39 pm26
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KX1600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KX1600 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info