497061
10
Zoom out
Zoom in
Previous page
1/88
Next page
10
ENGLISH
u Pull the plunge lock lever (4) up.
u Plunge the router down until the router bit touches the
workpiece.
u Push the plunge lock lever (4) down.
u Move the pointer (29) in the zero position on the scale (10).
u Add the desired depth of cut to the starting position.
u Move the depth stop bar (9) to the calculated position on
the scale.
u Tighten the locking screw (28).
u Fine adjust using the adjusting knob (30).
u Pull the plunge lock lever (4) up and let the router return to
its original position.
u After switching the router on, plunge it down and make the
desired cut.
Adjustingthedepthofcutusingapieceofwood(g.J)
u Fit the router bit and plunge the router down as described
above.
u Pull the depth stop bar (9) up.
u Place a piece of wood with a thickness equal to the
desired depth of cut between the depth stop (27) and the
depth stop bar (9).
u Tighten the locking screw (28).
u Fine adjust using the adjusting knob (30).
u Remove the piece of wood.
u Pull the plunge lock lever (4) up and let the router return to
its original position.
u After switching the router on, plunge it down and make the
desired cut.
Adjustingtherevolverdepthstop(g.K)
After turning the revolver depth stop to the desired setting, you
can ne-adjust the depth stop to be used. If you want to make
several cuts with a different depth of cut, adjust each of the
depth stops.
u Turn the depth stop screw (31) up or down as required
using a screwdriver.
Setting the speed
u Set the speed control knob (3) to the required speed.
Use a high speed for small diameter router bits. Use a low
speed for large diameter router bits.
Usingabattenasaguide(g.L)
When it is not possible to use the edge guide, for example
when routing grooves in the back panel of a bookcase to
support shelves, proceed as follows:
u Select a piece of wood with a straight edge to use as
a batten.
u Place the batten onto the workpiece.
u Move the batten until it is in the correct position to guide
the tool.
u Securely clamp the batten to the workpiece.
Usingthetemplateguide(g.D)
The template guide can be used to make a cutout shape from
a template, for instance a letter.
u Secure the template over the workpiece with double-sided
tape or ‘G' clamps.
u The router bit must extend below the ange of the
template guide, to cut the workpiece in the shape of the
template.
Usingthedistancepiece(g.E)
The distance piece can be used for trimming wooden or
laminate vertical projections.
Usingthecentringpin(g.F)
The centring pin can be used to cut out circular patterns.
u Drill a hole for the point of the centring pin in the centre of
the circle to be cut.
u Place the router on the workpiece with the point of the
centring pin in the drilled hole.
u Adjust the radius of the circle with the bars of the edge guide.
u The router can now be moved over the workpiece to cut
out the circle.
Usingthecopyfollower(g.G)
The copy follower helps to maintain an equal cutting distance
along the edge of irregularly shaped workpieces.
u Place the router on the workpiece at the desired distance
from the edge to be copied.
u Adjust the bars of the edge guide until the wheel is in
contact with the workpiece.
Switching on and off
Switching on
u Keep the lock-off button (2) depressed and press the on/
off switch (1).
u Release the lock-off button.
Switching off
u Release the on/off switch.
Warning! Always operate the tool with both hands.
Hints for optimum use
u When working on outside edges, move the tool
counterclockwise (g. M). When working on inside edges,
move the tool clockwise.
u Use HSS router bits for softwood.
u Use TCT router bits for hardwood.
u You can use the tool without a guide (g. N). This is useful
for signwriting and creative work. Only make shallow cuts.
u Refer to the table below for common types of router bits.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KW900E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KW900E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info