Manual Black Decker KW850 T1 (page 12 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

577912

Zoom out

Zoom in

1/100

ENGLISH

Fitting the centring pin (fig. O)

◆ Fit the edge guide to the router as shown in

fig. C, but upside down.

◆ Fit the centring pin (22) to the workpiece side

of the edge guide with the screw (23) provided.

Fitting the copy follower (fig. P)

◆ Fit the edge guide to the router as shown in

fig. C.

◆ Fit the ‘L’ bar (24) to the upper side of the edge

guide using the two screws and nuts provided.

◆ Fit the rotating attachment (25) to the ‘L’ bar

with the wing screw provided.

USE

Let the tool work at its own pace.

Do not overload.

◆ Carefully guide the cable in order to avoid

accidentally cutting it.

Adjusting the depth of cut (fig. E)

The depth of cut is the distance X between the

depth stop bar (9) and the depth stop (18).

The depth of cut can be set in two different ways

as described below.

Adjusting the depth of cut using a piece of wood

(fig. A & F)

◆ Fit the router bit as described above.

◆ Loosen the locking screw (10).

◆ Pull the plunge lock lever (4) up.

◆ Plunge the router down until the router bit

touches the workpiece.

◆ Push the plunge lock lever (4) down.

◆ Pull the depth stop bar (9) up.

◆ Place a piece of wood with a thickness equal to

the desired depth of cut between the depth

stop (18) and the depth stop bar (9).

◆ Tighten the locking screw (10).

◆ Remove the piece of wood.

◆ Pull the plunge lock lever (4) up and let the

router return to its original position.

◆ After switching the router on, plunge it down

and make the desired cut.

Adjusting the depth of cut using the scale

(fig. A & G)

◆ Fit the router bit as described above.

◆ Loosen the locking screw (10).

◆ Pull the plunge lock lever (4) up.

◆ Plunge the router down until the router bit

touches the workpiece.

◆ Push the plunge lock lever (4) down.

◆ Read the starting position from the scale (11).

◆ Add the desired depth of cut to the starting

position.

◆ Move the depth stop bar (9) to the calculated

position on the scale.

◆ Tighten the locking screw (10).

◆ Pull the plunge lock lever (4) up and let the

router return to its original position.

◆ After switching the router on, plunge it down

and make the desired cut.

Adjusting the revolver depth stop (fig. H)

After turning the revolver depth stop to the desired

setting, you can fine-adjust the depth stop to be used.

If you want to make several cuts with a different

depth of cut, adjust each of the depth stops.

◆ Turn the depth stop screw (19) up or down as

required using a screwdriver.

Setting the speed (fig. A)

◆ Set the speed control knob (3) to the required

speed. Use a high speed for small diameter

router bits. Use a low speed for large diameter

router bits.

Using a batten as a guide (fig. I)

When it is not possible to use the edge guide,

for example when routing grooves in the back

panel of a bookcase to support shelves,

proceed as follows:

◆ Place a batten onto the workpiece.

◆ Move the batten until it is in the correct

position to guide the tool.

◆ Securely clamp the batten to the workpiece.

Using the template guide (fig. M)

The template guide can be used to make a cutout

shape from a template, for instance a letter.

◆ Secure the template over the workpiece with

double-sided tape or ‘G’ clamps.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KW850 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker KW850 T1 Manual

Product: