578046
6
Zoom out
Zoom in
Previous page
1/12
Next page
6
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for planers
Wait for the cutters to stop before setting the tool
down. An exposed cutter may engage the surface and
lead to possible loss of control and serious injury.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Shavings discharge outlet
4. Planing depth adjustment knob
5. Planing depth graduation
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Replacing the cutting blades (fig. A)
The cutting blades provided with this tool are reversible.
Replacement cutting blades can be obtained from your local
retailer.
Removing
Loosen the bolts (6) using the spanner supplied.
Slide the blade (7) out of the holder (8).
Reverse the blade so that the unused side comes in position.
If both sides are worn, the blade must be replaced.
Fitting
Slide the blade into the holder until it is centred in the holder.
Make sure that the holder remains centred in the barrel (9).
Tighten the bolts using the spanner supplied.
Always replace both cutters.
Adjusting the depth of cut (fig. B)
The depth of cut is indicated by the marking (10). The setting
range can be read from the graduation (5).
Turn the planing depth adjustment knob (4) to the required
depth of cut.
Turn the knob to the ‘P’ postion whenever the tool is not in use.
Fitting and removing the parallel fence (fig. C)
The parallel fence (11) is used for optimum control on narrow
workpieces.
Hold the parallel fence (11) in front of the tool as shown.
Fit the parallel fence by inserting the locking knob (12)
into the hole (13).
Tighten the locking knob.
To remove the parallel fence proceed in reverse order.
Fitting and removing the rebating depth stop (fig. D)
The rebating depth stop (15) is used for limiting the planing
depth during rebating.
Hold the stud (16) in front of the tool as shown.
Fit the rebating depth stop by inserting the locking knob (17)
into the hole (18).
Fasten the locking knob.
To remove the rebating depth stop proceed in reverse order.
Adjusting the shavings discharge outlet (fig. E)
The tool facilitates both left-hand and right-hand side
shavings discharge.
Insert the adaptor (19) into the desired outlet opening,
aligning the notch with the recess. Twist the adaptor
clockwise as soon as it is fully inserted.
Insert the plug (20) into the opposite opening, following
the above procedure.
Provide for a suitable dust extraction.
Fitting and removing the shavings bag (fig. F)
Slide the shavings bag (21) into the shavings discharge
outlet (3).
Push the shavings bag into place. Make sure that the lug
(22) is correctly located into the hole (23) on the inside of
the shavings bag.
To remove the shavings bag, press the tab (24) and pull
the shavings bag out of the outlet.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KW82 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KW82 T1 in the language / languages: English as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KW82 T1

Black Decker KW82 T1 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info