577910

Black Decker KW800 T1 Manual

27
Zoom out
Zoom in
Previous page
1/80
Next page
27
ENGLISH
FITTING THE ROUTER BIT
Disconnect the plug from the electricity supply.
If a router bit is
already fitted,
press the spindle
lock button and
release the collet
clamp nut, using
the spanner
provided.
Insert the router
bit. Make sure it
protrudes at least
3mm from the end
of the shank.
Press the spindle
lock button and
tighten the collet
clamp nut using the spanner provided.
ADJUSTING THE DEPTH OF CUT
The depth of cut
is the distance (x)
between the triple
depth stop and
the depth stop bar.
Each router bit
varies in length
and the triple
depth stop
provides three different positions. Use one of the
following methods to set the depth of cut.
USING A PIECE OF WOOD
The most common method is to use a piece of wood as
a gauge as follows:
• Fit the router bit.
• Loosen the wing screw.
• Pull the plunge lock lever up.
• Plunge your router down until the cutter is in contact
with the workpiece.
• Push the plunge lock lever down to hold your
router in this position.
Pull up the depth
stop bar.
Put a piece of
wood of the same
thickness as the
desired depth of
cut, between the
depth stop bar
and the triple
depth stop.
• Tighten the wing screw.
• Remove the piece of wood.
• Pull the plunge lock lever up to move your router
back to its original position.
• Move your router to its working position and set the
on/off switch to ‘I’.
• Plunge your router down to the workpiece and
push the plunge lock lever to hold your router at
this depth.
• Make the desired cut.
USING THE SCALE
Proceed as follows:
• Fit the router bit.
• Loosen the wing screw.
• Pull the plunge lock lever up.
• Plunge your router down until the cutter is in contact
with the workpiece.
• Push the plunge lock lever down to hold your router
in this position. The scale on the depth stop bar now
shows the starting position. This starting position
will vary, depending on the cutter used.
• Add the desired depth of cut to the starting position;
for example, if the scale shows 23mm and the
desired depth of cut is 10mm, the correct adjustment
on the scale is 23 +10 = 33mm. If the scale shows
46mm and the desired depth of cut is 5mm, the
correct adjustment on the scale is 46 + 5 = 51mm.
• Move the depth stop bar to the calculated number.
• Clamp the depth stop bar with the wing screw.
• Pull the plunge lock lever up to move your router to
its original position.
• Move your router to its working position and set the
on/off switch to ‘I’.
• Plunge your router down to the workpiece and
push the plunge lock lever to hold your router at
this depth.
• Make the desired cut.
• For better quality cuts and a longer cutter life, make
a series of cuts, instead of a single cut.
x
3mm
KW800_E ML p24-41 16-01-2001, 13:4527
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KW800 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KW800 T1 in the language / languages: German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KW800 T1

Black Decker KW800 T1 User Manual - English - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info