578041
5
Zoom out
Zoom in
Previous page
1/56
Next page
5
ENGLISH
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Additional safety instructions for Australia and
New Zealand
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Additional safety instructions for planers
Remove all nails and metal objects from the workpiece
before planing.
Always hold the tool with both hands and by the handles
provided.
Use sharp cutting blades only.
Never put the tool down until the cutting blades have
come to a complete standstill.
Immediately disconnect the cable from the mains if it is
damaged or cut.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Shavings discharge outlet
4. Planing depth adjustment knob
5. Planing depth graduation
Assembly
Warning! Make sure that the tool is switched off and
unplugged.
Replacing the cutting blades (fig. A)
The cutting blades provided with this tool are reversible.
Replacement cutting blades can be obtained from your local
retailer.
Removing
Loosen the bolts (6) using the spanner supplied.
Slide the blade (7) out of the holder.
Reverse the blade so that the unused side comes in
position. If both sides are worn, the blade must be
replaced.
Fitting
Slide the blade into the holder until it is against the end
stop.
Tighten the bolts using the spanner supplied.
Always replace both cutters.
Adjusting the depth of cut (fig. B)
The depth of cut is indicated by the marking (8). The setting
range can be read from the graduation (5).
Turn the planing depth adjustment knob (4) to the required
depth of cut.
Turn the knob to the ‘P’ postion whenever the tool is not
in use.
Fitting and removing the parallel fence (fig. C)
The parallel fence is used to for optimum control on narrow
workpieces.
Loosen the locking knob (9).
Insert the parallel fence (11) through the opening (10).
Slide the parallel fence into the desired position.
Tighten the locking knob.
To remove the parallel fence proceed in reverse order.
Connecting a vacuum cleaner to the tool (fig. D)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool. The adaptor can be purchased from your
local Black & Decker retailer.
Slide the adaptor (12) over the shavings discharge outlet (3).
Connect the vacuum cleaner hose (13) to the adaptor.
Assembling and fitting the shavings collection bag (fig. E)
The shavings collection bag is particularly useful when
working in confined spaces.
Before first use, you will have to assemble the shavings
collection bag.
Fit the wire frames (14) to the connecting plate (15) using
the screws (16) and washers (17).
Pull the cloth bag (18) over the frame structure as shown.
Take care that the elasticated mouth (19) is well fitted
around the edge of the connecting plate (15).
Slide the connecting plate over the shavings discharge
outlet (3).
Use
Adjust the depth of cut.
If necessary, fit and adjust the parallel fence.
Use sharp cutters only.
Switching on and off
Switching on
Keep the lock-off button (2) depressed and press the on/
off switch (1).
Release the lock-off button.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KW712 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KW712 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KW712 T1

Black Decker KW712 T1 Quick start guide - English - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info