581121
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
ENGLISH
(Original instructions)
9
ENGLISH
(Original instructions)
u Use a ne-tooth saw blade.
u Saw from the back surface of the workpiece.
u To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw through
this sandwich. Alternatively, t the anti-splinter guard (13)
that is supplied with your product. (KS901SE only).
Sawing metal
Warning! Do not use a vacuum when cutting metal. Metal
lings will be hot and may cause re.
Be aware that sawing metal takes much more time than
sawing wood.
u Use a saw blade suitable for sawing metal.
u When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut through
this sandwich.
u Spread a lm of oil along the intended line of cut.
Rip Fence
Ripping and circle cutting without a pencil line are easily done
with a rip fence and circle guide (available as an optional extra
- part number X43005-XJ).
Attaching Rip Fence (gs. H & I)
u Insert rip fence (14) into the shoe plate slots with the cross
bar facing down as shown in gure H.
u Place screw (15) into hole in bottom of shoe plate.
u Align clamp bar (16) over screw with lipped edge facing
down and pointing towards the rear of the saw.
u Using a phillips screwdriver, run the screw into the
threaded hole in the bar clamp as shown in gure I.
u Adjust to width of cut and tighten screw.
Circle Cutting (g. J)
u Insert rip fence into slot on the right side of shoe plate with
cross bar facing up.
u Adjust rip fence so that distance from blade to hole in
cross bar is the desired radius and tighten screw.
u Place saw so that centre of hole in cross bar is over centre
of circle to be cut (make plunge cut, drill hole for blade or
cut inward from edge of material to get blade into posi-
tion).
u When saw is properly positioned, drive a small nail
through hole in cross bar into exact centre of circle to be
cut.
u Using rip fence as a pivot arm, begin cutting circle.
Plunge Cutting (g. K)
A plunge cut is an easy method of making an inside cut. The
saw can be inserted directly into a panel or board without rst
drilling a lead or pilot hole. In plunge cutting, measure the sur-
face to be cut and mark clearly with a pencil. Next tip the saw
forward until the front end of the shoe sits rmly on the work
surface and the blade clears the work through its full stroke.
Switch the tool on and allow it to attain maximum speed. Grip
the saw rmly and lower the back edge of tool slowly until the
blade reaches its complete depth. Hold the shoe at against
the wood and begin cutting. Do not remove blade from cut
while it is still moving. Blade must come to a complete stop.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
u Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Never let any liquid get inside the tool and never immerse
any part of the tool into liquid.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be tted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the tting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you nd one day that your BLACK+DECKER product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
BLACK+DECKER provides a facility for the collection and re-
cycling of BLACK+DECKER products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS901PEK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS901PEK in the language / languages: English as an attachment in your email.

The manual is 3,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS901PEK

Black Decker KS901PEK User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info