581098
8
Zoom out
Zoom in
Previous page
1/16
Next page
8
all parts of the operating cycle such as the times when the
tool is switched off and when it is running idle in addition to
the trigger time.
Labels on tools
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
This appliance is not intended for use by young or infirm
persons without supervision. Children must be
supervised to ensure they do not play with the
appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Additional safety instructions for non-rechargeable
batteries
Never attempt to open for any reason.
Do not store in locations where the temperature may
exceed 40°C.
When disposing of batteries, follow the instructions
given in the section "Protecting the environment".
Do not incinerate the batteries.
Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries, proceed as
follows:
- Carefully wipe the liquid off using a cloth. Avoid skin
contact.
Additional safety instructions for lasers
This laser complies with class 2 according to EN 60825-
1:2007. Do not replace a laser diode
with a different type. If the laser is damaged
, have the laser
repaired by an authorised repair agent.
Do not use the laser for any purpose other than projecting
laser lines.
An exposure of the eye to the beam of a class 2 laser is
considered safe for a maximum of 0.25 seconds. Eyelid
reflexes will normally provide adequate protection. At
distances greater than 1m, the laser complies with class 1
and is therefore considered completely safe.
Never look into the laser beam directly and intentionally.
Do not use optical tools to view the laser beam.
Do not set up the tool where the laser beam can cross any
person at head height.
Do not let children come near the laser.
Features
1. Lock-on button
2. On/off switch
3. Blade storage compartment cover
4. Shoe plate locking lever
5. Dust extraction outlet
6. Dust extraction adaptor
7. Shoe plate
8. Auto Select
TM
dial
9. Blade support roller
10. Tool-free blade clamp
Additional features (fig. A)
Additional features may be applicable depending upon the
product purchased. The additional features applicable to the
catalogue number purchased are shown in fig. A.
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and that
the saw blade has stopped. Used saw blades may be hot.
Fitting the saw blade (fig. B)
Hold the saw blade (11) as shown, with the teeth facing
forward.
Push and hold the blade clamp (10) down.
Insert the shank of the saw blade into the blade holder (12)
as far as it will go.
Release the blade clamp (10).
Saw blade storage (fig. C)
Saw blades (11) can be stored in the storage compartment
located on the side of the tool.
Open the cover (3) of the saw blade storage compartment
by holding the tab on the top of the cover (3) and pulling it
outward.
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Read all of this manual carefully.
This product is not to be used by children
under 16.
Laser radiation.
Do not look into the laser beam.
Do not use optical tools to view the laser
beam.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS900SL T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS900SL T1 in the language / languages: English as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS900SL T1

Black Decker KS900SL T1 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info